This is my first so be easy....I have some questions.....

1. What do you use to cut out the hole? I am assuming a drill but i am not 100% certain.

2. What is the best way to go about mounting the license plate? I noticed there are no holes marked so i am interested in how you guys did it.

I want to get this mounted by the end of the week so i can go ahead and get it painted. Thanks in Advance.......

_____________________________________________
Jerrome B.
1995 GSX - Race
1997 GST - Drive
1995 GST - Who the hell knows

>This is my first so be easy....I have some questions.....
>
OK

>1. What do you use to cut out the hole? I am assuming a drill
>but i am not 100% certain.

yeah, when making the holes use a drill and when you do it, put the bumper on the car and pull it out a lil, then mark where the holes are


>2. What is the best way to go about mounting the license
>plate? I noticed there are no holes marked so i am interested
>in how you guys did it.

I just mesured in the center and used bolts to hold it on
>
>I want to get this mounted by the end of the week so i can go
>ahead and get it painted. Thanks in Advance.......


sure

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

what i did was:

take off both rear wheels
take off the plastic in the fender well
take the trunk plastic interior out
take out the taillights
get the bolts under the bumper and on top of it (where the taillights were)
get the one bolt from the fender well on both sides
get the 2 bolts from the inside trunk
get the bumper off
get the license plate light thingy
cut the holes on the bumper if needed
stretch the body kit (someone pull from both sides)
put it on and try gettin the sides to look pretty
when they do drill w/ selftapping screws about 6 of em in the middle to bolt the bumper down
then work on the sides
start w/ one from the fender well
for the other one you can fit a drill in there w/ self tapping screws
but for the top part on the side on the drivers side i had to use a powerscrew driver to get that in
on the otherside i had to drill a hole out the side of the car
and then drill a hole in the body kit top
and then push it in and pop a screw in cuz of the gas door

..blah i hope you understood any of this i usually dont make sense when im blazed

peace

____________________________________

Another BANNED asshole.

Charlie....you think you can help me with this this weekend? I have the front on sort of but need alittle help with the back and sides.....I also need a hook on the painting of it.....let me know......

_____________________________________________
Jerrome B.
1995 GSX - Race
1997 GST - Drive
1995 GST - Who the hell knows

>>This is my first so be easy....I have some questions.....
>>
>OK
>
>>1. What do you use to cut out the hole? I am assuming a
>drill
>>but i am not 100% certain.
>
>yeah, when making the holes use a drill and when you do it,
>put the bumper on the car and pull it out a lil, then mark
>where the holes are

Well with this kit the holes are pre marked....just need to be punched out.....

_____________________________________________
Jerrome B.
1995 GSX - Race
1997 GST - Drive
1995 GST - Who the hell knows

You can use a dremel to make holes too. Don't forget to make holes for the license plate lights.

95 GST | So-Cal

>You can use a dremel to make holes too. Don't forget to make
>holes for the license plate lights.

I was going to leave those out....are they needed by law?

_____________________________________________
Jerrome B.
1995 GSX - Race
1997 GST - Drive
1995 GST - Who the hell knows

License plate lights are needed by law, i was able to actually transfer all teh plate "accessories" behind the bumper onto my friends bomex with no probs. But on my other friends blitz, the shop just bolted it on and bent it a lil "so it flowed with the kit".

PS.....I did call you back a few times. I must not have heard your number right on my voice mail though. The operator kept saying it was out of service n whatnot....My bad mang

>
>The operator kept
>saying it was out of service n whatnot....My bad mang



PWN3D

https://www.kaptainmyke.com

>License plate lights are needed by law, i was able to
>actually transfer all teh plate "accessories" behind the
>bumper onto my friends bomex with no probs. But on my other
>friends blitz, the shop just bolted it on and bent it a lil
>"so it flowed with the kit".
>
>PS.....I did call you back a few times. I must not have heard
>your number right on my voice mail though. The operator kept
>saying it was out of service n whatnot....My bad mang

I will give you a call again....I want to ask you something. Not sure what happened there.

_____________________________________________
Jerrome B.
1995 GSX - Race
1997 GST - Drive
1995 GST - Who the hell knows