anyone else's moonroof rattle like hell? how do u tighten it? the 6 torx screws on it? tia


96RS ~ full 99GS Special Edit. body conversion, aem cai, greddy header, afx pulley, B&M SS, magecores & NGKs, A/F and Volt guages, Sparco Torino Seat, illuminas, prokits, ingalls camber, gunmetal GS rims, ST Sways, STBs, lower rear tie bar, Sony Xplode head, Xplode 10 disk, Boston Components, 2 Kenwood amps, 12" MTX sub, a shit load more.


97GSX ~ 18psi~ Ported/Clipped 15 degrees Frank 2 w/46trim, Ported Exh. housing, Tial 40mm External Wastegate with discharge tube, Ported O2 housing, 3" downpipe, 3" Straight Pipe, Apex N1, fake cat, K&N FIPK, Greddy IC Piping, Type S bov, S-AFC, Profec B, Greddy TT, Slimline Fan, RRE Catch Can, Greddy Big FMIC, ND 660s, Walboro 190lph, ACT 2600 w/street disk, clutch SS line, lighten flywheel, removed cruise control line, Greddy EGT, Coolant, Boost Gauges, motor mount inserts, Magnecor & plugs, greddy oil cap, greddy radiator cap, AEM big brake upgrade w/MM pads, MOMO Race steering wheel, Ground Controls Coilovers, Koni Yellows, Ingalls Camber Kit, F&R STBs and free mods. To all the haters _|_ tia

The Original 2GNT []D[][]Y[][]D


96 RS


97 GSX

take those 6 torx screws out. Raise the glass out the top and set it aside. Push the sunroof button so that it slides back about halfway. Somewhere along the middle of the tracks, there is another torx screw that goes through a flat piece that has a 'finger' on it that extends partway across the track to hold it down. Typically this is loose, so tighten it down. While you're in there, you might as well make sure the rest of the screws are tight as well.

Even if you get them all tight, it might not completely quiet the problem. their design sucks and some will rattle regardless. Making sure all the screws are tight will make it fairly quiet though. Good luck

Matt

99GS MT | Star Stage 2 | GC coilovers | HurriganeGS tie bars | Tokico Illuminas | 17x7 Enkei RS5 | Baer track brakes |+

^^^^

never tried, but sounds good to me! Been wondering how to do that...

TIA!

- ghost




Ghost's Beginning College Guide:

http://www.cosmomag.com/

factory service manual http://www.ecanfix.com/users/manualcd/gift/dsm/index.html

yea thanks man.. i tried to tighten all 6 of those torx screws the other day but they were all tight..now i have to go try this....





'95 Eclipse RS
INTERIOR
-Red Painted Accents
-Reverse EL Gauges
AUDIO
-Sony CDXM 750 Head Unit
-2 JL Audio 12w0 subs
-Pioneer Premiere Amp
-CompuStar 2WAS Alarm with Remote Start and Pager
-Optima Yellow Top Battery
EXTERIOR
-Enkei 15" wheels (came with the car)
-2nd Generation Altezza Tails
-Clear Bumper Lenses
-APC Speed Glo Mirrors (with turn signals)
-Red LED Washer Nozzles
PERFORMANCE
-K&N Filter
-Energy Suspension Motor Mount Inserts

ONe more thing I thought of a few minutes ago. when you're putting it back together...
put the glass back in and then put the 6 torx screws in, but don't tighten them.

pick a side and make sure the front is even with the lines of the car then tighten the front screw while holding hte glass in place. it's possible with one person, but much easier w/ 2. Then line the back up and tighten the back screw. then tighten the middle. Repeat on the other side.

99GS MT | Star Stage 2 | GC coilovers | HurriganeGS tie bars | Tokico Illuminas | 17x7 Enkei RS5 | Baer track brakes |+

I completely disassembled, cleaned, and lubricated the entire assembly, along with re-timing the sunroof ECU/motor. Re-greasing the cables made it slide soooo nicely. And now, I have no (!!!) rattles (from the roof, anyways). Took me all night. Am I nuts? Yes. Was it worth it? Most definately.
-=B-=

Dude, Boeing called. They want their wing back.

Dark0ne95: There is a butthole on that girl that his going to feel the wrath of 23 yeras of worldwide hate.
Me: Can I put that in my sig?
Dark0ne95: GO right fucking ahead.

thanks all! ill try it!


96RS ~ full 99GS Special Edit. body conversion, aem cai, greddy header, afx pulley, B&M SS, magecores & NGKs, A/F and Volt guages, Sparco Torino Seat, illuminas, prokits, ingalls camber, gunmetal GS rims, ST Sways, STBs, lower rear tie bar, Sony Xplode head, Xplode 10 disk, Boston Components, 2 Kenwood amps, 12" MTX sub, a shit load more.


97GSX ~ 18psi~ Ported/Clipped 15 degrees Frank 2 w/46trim, Ported Exh. housing, Tial 40mm External Wastegate with discharge tube, Ported O2 housing, 3" downpipe, 3" Straight Pipe, Apex N1, fake cat, K&N FIPK, Greddy IC Piping, Type S bov, S-AFC, Profec B, Greddy TT, Slimline Fan, RRE Catch Can, Greddy Big FMIC, ND 660s, Walboro 190lph, ACT 2600 w/street disk, clutch SS line, lighten flywheel, removed cruise control line, Greddy EGT, Coolant, Boost Gauges, motor mount inserts, Magnecor & plugs, greddy oil cap, greddy radiator cap, AEM big brake upgrade w/MM pads, MOMO Race steering wheel, Ground Controls Coilovers, Koni Yellows, Ingalls Camber Kit, F&R STBs and free mods. To all the haters _|_ tia

The Original 2GNT []D[][]Y[][]D


96 RS


97 GSX

stupid question...What did you use to lube up the sunroof? I need to tighten mine badly, it sounds like its gonna fall off and I might as well lube it up while im at it...Thanks alot.

1997 Eclipse GS
AEM CAI
Apex'i N1 Catback
Greddy Header
5% window tint
Front-Rear-Lower Rear STB's
Yellow Painted Calipers
1st gen altezzas with original painted center piece
Soon-Tokico Illum's or Blues

I've been told to use lithium grease in the rails



stock 95rs=backroad rally champion

Lane Adams

1998 GST Spyder
1995 GSX
1995 TSI AWD

I found a spray lithium grease. You spray it in as a liquid, and it coagulates (gels up) a bit, and turns into grease. I would spray a bit into the rails, and onto the cables since you should remove them. Don't forget to re-allign the timing marks on the sunroof ECU.
-=B-=

Dude, Boeing called. They want their wing back.

Dark0ne95: There is a butthole on that girl that his going to feel the wrath of 23 yeras of worldwide hate.
Me: Can I put that in my sig?
Dark0ne95: GO right fucking ahead.

aite ive got another really stupid question... I remove the glass by taking out the 6 screws then what do I do? What do you mean realign the sunroof motor? Thanks.

1997 Eclipse GS
AEM CAI
Apex'i N1 Catback
Greddy Header
5% window tint
Front-Rear-Lower Rear STB's
Yellow Painted Calipers
1st gen altezzas with original painted center piece
Soon-Tokico Illum's or Blues

just start takin it apart and anyone can figure out whats up. i replaced both my rails and it took me about 2 and a half hours its hella easy
later
"Z"

what do you use to unscrew the hexx screws? Some special head on a screwdriver?

Can you post specifically how to retime the ECU?

If i had never gotten into cars, i could still afford to eat.

sears has the torq bits.
and i have no idea on retimeing the ecu but i did not have to retime anything when i changed the rails.
later
"Z"

Well, if you get deep into the bowells of the sunroof assembly, you will get to the sunroof ECU/sunroof motor. It is one unit that the cables come out of. There is a window on the side of it, and a gear to turn. You want to look in the window and line up the 2 white lines (timing marks) by turning the gear one way or the other. It is all explained in the FSM.
-=B-=

Dude, Boeing called. They want their wing back.

Dark0ne95: There is a butthole on that girl that his going to feel the wrath of 23 yeras of worldwide hate.
Me: Can I put that in my sig?
Dark0ne95: GO right fucking ahead.

mine only does it for a little while when im driving but then stops. I might try this. Thanx.

2003 Acura RSX Type-S
15.042 @ 93.06
Devon
Creator of one of the longest and most controversial posts in 2gnt history...
http://forums.2gnt.com/dcboard.php?az=show_topic&forum=38&topic_id=112462&mesg_id=112462&page=