What else do you need to hook these LEDS to a 12 volt source? What resisters or anything?

venomtalon@aol.com

Performance Mods: Custom CAI, Jeep 60mm TB, Ported Intake Manifold with Jeep TB match, 5 angle valve job, Head milled .020, Regrind Cams, PT Lifters and Rockers, AEM Cam Gears, OBX Wires, NGK Plugs, AFX UDP, OBX Header, OBX

go to my site and it will tell you everything you need to know about leds

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

you will need a 330ohm resistor and the wilingness to experiment

-Jason

97 Talon ESi-T (forever in progress...)


95 GS (Gone)
16.74@83.18mph
119.8 whp - 113.3 lbs/ft


2GNT #677
My Wiki Page: www.2gnt.com/index.php?d=Iamnotwhoiam
Pictures: http://picasaweb.google.com/iamnotwhoiam/Talon/

So does it go like: positive-->330 ohm-->one side of LED: and the other side goes to the groung?

venomtalon@aol.com

Performance Mods: Custom CAI, Jeep 60mm TB, Ported Intake Manifold with Jeep TB match, 5 angle valve job, Head milled .020, Regrind Cams, PT Lifters and Rockers, AEM Cam Gears, OBX Wires, NGK Plugs, AFX UDP, OBX Header, OBX

Your web page wont work. It says there is to much data transfer.

venomtalon@aol.com

Performance Mods: Custom CAI, Jeep 60mm TB, Ported Intake Manifold with Jeep TB match, 5 angle valve job, Head milled .020, Regrind Cams, PT Lifters and Rockers, AEM Cam Gears, OBX Wires, NGK Plugs, AFX UDP, OBX Header, OBX

give the site a mmin, I wont pay them so I dont get that much data transfer

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

yep.. and the led works on a pos/neg and the positive side of the led is the one with the longer lead(wire) but that is the opposite for the red leds for some strange reason.

-Jason

97 Talon ESi-T (forever in progress...)


95 GS (Gone)
16.74@83.18mph
119.8 whp - 113.3 lbs/ft


2GNT #677
My Wiki Page: www.2gnt.com/index.php?d=Iamnotwhoiam
Pictures: http://picasaweb.google.com/iamnotwhoiam/Talon/

Ok sounds good. What i'm doing is lighting up some autometer gauges. I got some phantom ones and want them to light up blue. Do you think I should use Blue LED's or just buy some blue lights that fit in the harness autometer gives you?

venomtalon@aol.com

Performance Mods: Custom CAI, Jeep 60mm TB, Ported Intake Manifold with Jeep TB match, 5 angle valve job, Head milled .020, Regrind Cams, PT Lifters and Rockers, AEM Cam Gears, OBX Wires, NGK Plugs, AFX UDP, OBX Header, OBX

if you can find blue bulbs then it would be a little easier to hookup, but otherwise id go for the led.. all my gauges will probably be led lit

-Jason

97 Talon ESi-T (forever in progress...)


95 GS (Gone)
16.74@83.18mph
119.8 whp - 113.3 lbs/ft


2GNT #677
My Wiki Page: www.2gnt.com/index.php?d=Iamnotwhoiam
Pictures: http://picasaweb.google.com/iamnotwhoiam/Talon/

My autometer gauges use 194's so go pick up some 194B's that's what I did, they light up nice blue... if you have a good power supply to them.

"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, Crane Fireball HI-6DI2, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors & Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold 1/2, Rear disc brake conversion kit w/, Rear KVR Cross Drilled Rotors & Carbon Fiber Kevlar Pads, SS Brake Lines

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.