Ok, this is another Attempt at filling what used to be the Holes for my Non-Turbo Spoiler, Power Antenna, and Rear Wiper Arm. Most of you said to Weld it (would be the best) and I Agreed, but due to Lack of Funds and Refusing to trade an Arm and a Leg to some Body Shop for Services.. What else would work? I have two Neighbors who are Retired Carpenters (not that they know too much about Cars..) And they've both Reccomended trying J.B. Weld and Sanding it down afterwards. An actual Retired Welder (who's a friend of one of the two Carpenters) was the one who Initially Reccomended using the stuff, said it worked good on stuff like Washers, Dryers, and Fridges. What do you guys think? And if it would work.. How would I go about with the Procedure? I've never used it.. Thanks a lot.

-MIKE-

Stroked 2.2L

since its your sencond attemp jus do it the right way and weld it . Jb weld wont work that great

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

jb weld works great in some places. body work is not one of them.

do it right and weld it up or at the very least glass it up. jb weld doesn't hold up under paint for some reason.

Erik P.
Official 2GNT thread Hijacker
Some say that he's driven over more Covenant than he's shot, and that his grenades aren't where you'd expect them to be...
All we know is, He's not The Stig... But he is The Stig's Spartan cousin!

I remember reading a write-up on an S2000 site a few years back where a guy filled the holes with silicon and then put some rubber washers on top of the holes. He then painted the top of the rubber washers the same color as his car and it turned out pretty good. It's ghetto as hell but may be a temporary solution if money is tight. You can always pull them off once you have the money to have a shop do it.

I contributed to the Wiki!
EVO IX - just a really expensive boost gauge and a K&N air filter
96 Eclipse RS -awaiting registration and inspection
95 Eclipse GS - parts car
Mods/Profile - http://www.2gnt.com/index.php?d=cs82685

I found a guy to do the Welding for Cheap. He works at a Local Muffler Shop and was Reffered by a guy who does Body Work in Partnership with him on the side. He said go Buy a 3x3' Sheet of Sheet Metal (What Thickness?) and Pre-Cut the Pieces ahead of time (Overlap them a bit, but how much?) and then have the guy Weld them on and Grind them down? Does that sound about right?

I'd do the nails through the holes trick myself

Erik P.
Official 2GNT thread Hijacker
Some say that he's driven over more Covenant than he's shot, and that his grenades aren't where you'd expect them to be...
All we know is, He's not The Stig... But he is The Stig's Spartan cousin!