My friend has a 1997 GST. It was having some vibration problems. I check the balance shaft and the tensioner was kind of loose. I fix that and the vibration went away. Now, he is telling me that after 65mph, the car start to vibrate. Something wierd is that there is almost no space between the bottom of the engine/transmission and the black frame support that goes from the bottom radiator support to the back of the engine maybe, maybe .25 inch separation. Well, I changed the broken side engine and front engine mounts, but still the same. The other two are in good condition and there still no space between the engine/transmission and the support.

Well, I for one have noticed that both cars I have, a '91 GSX and '92 Acura Vigor get the shakes between 65 and 70 MPH (and a bit higher) on the highway. There is noticable vibration at that speed in both cars, which I think is perfectly normal. I don't have the slightest clue as to your exact situation, but vibration at speed is normal as far as I know. No problems have arisen out of either car as a result of this vibrating.

Not particularly helpful I guess but it might just be simple harmless vibration.

It's running again shitheads.

http://www.dsmregistry.com/detail.php?carid=791

HybriDSM@gmail.com ; HybriDSM@hotmail.com

Think for yourself. Question authority does not always mean disagree with authority.

If life were perfect, I'd be Calvin and you'd be Hobbes.

I know him like 2 years now. Since he has the car I notice, yes, a little vibration. In November 2003, he was going to west Palm Beach and in I-95 he hit a bump. His slave line broke, don't know how. He was probably at 65-75mph. Could that hit cause the support to bend and to get the shaft balance so loose? Is there anyway that I can raise the engine/transmission from the support? Because with that vibration the engine/transm. hits the support and make noise. Also, the driver side rubber cushion in the middle of the axle is loose. You can turn the rubber over the axle.
Thanks

__________________________________________________________
-Tony <--- NOT asian.
'06 Wicked White EVO IX

The cv joint doesn't make any noise in any direction. Looks like is fine. But I will try to make an extensive check on those. Anything else that I can check?

Thanks.



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges

there is an inner and an outer CV joint. I assumed you were talking about the inner one. Yes?
nice car BTW.

__________________________________________________________
-Tony <--- NOT asian.
'06 Wicked White EVO IX

Well, there are a total of four CV joints. All of them look OK. The rubber I am talking is the one on the longer axle. This small rubber turns around the axle instaead of being fixed to the axle. Do you know which one I'm talking about?

Oh!, Thank you.



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges

Every DSM I have ever been in vibrates at 65mph. Don't worry about it. My Talon does it, Matt's GSX does it, my roommate's Talon did it, etc. They all do it. My car did it on two different sets of wheels. 65mph is the magic number. It goes away after 70-75mph right?

I just came from a test drive! It is not as he told me. The vibration starts as soon as you step on the gas, hard acceleration. It is running great, but it is just that big vibration.It just a steady vibration. I felt it on the driver side. Also, the engine is resting on the support below. Is this like that on the GST's or there has to be a gap?



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges

hmmm. now that you mention it, mine makes a weird noise around 50-60 ish. Not so much a vibration you can feel, but can be heard. Comes from the passenger side front end.

__________________________________________________________
-Tony <--- NOT asian.
'06 Wicked White EVO IX

Wait, the engine is resting on the cross member? Look for broken engine mounts.

At that speed or under acceleration. Also, the space between the engine/tranny and the bottom support is there a gap or resting on it?



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges

No, it should not be resting on it. Sounds like it could be a broken motor mount.

mine does not vibrate at anyspeeds..not even at 135mph.
has it been alinged?
if it was a broken engine mount you would get wheel hop like crazy.. believe me on my 7bolt the front and the back where broken..

and you say that that the wheels have also been balanced?

yeah balance the wheels then don't worry about it, it could be 1093741723947237 things. Mine does it, I think the CV joint is going, and it got better when I replaced the rear struts (blown) with new ones but not perfect. Bascially what i'm saying is tracking down this vibration after very basic stuff (alignment, wheel balancing) isn't worth it. I looked into it a while ago (search, you'll prob find it) and it has the potential to be SUPER expensive and yeild no results. It could be engine mounts, suspension bushings, struts, bent control arms, wheel cupping, wheel balancing, alignment, TIRE CHOICE, etc. as long as its not so intense as to be obnoxious, i'd just let it be. What I would look at, though, is that cross member....

vandy

P.S. i've heard aftermarket rims are incredibly hard to balance, and seeing as you have them, that may be the problem...

---------------------------------------

Black 98 GST missing her owner and looking for a new one...Inquiries welcome

OK! Thanks guys. I will check what can I do with the engine/tranny. All four engine mounts are in good condition. Will let you know what I find.



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges

91 awd: 60-1, 880's, E-Prom, etc.
93 awd: JDM 6 bolt, K&N, full exhaust, Wally 255, otherwise stock.

R.I.P. the original "Factory Freak"
15.5's with short ram and catback only
1996 RS 5-speed

Or is that AWD only?

91 awd: 60-1, 880's, E-Prom, etc.
93 awd: JDM 6 bolt, K&N, full exhaust, Wally 255, otherwise stock.

R.I.P. the original "Factory Freak"
15.5's with short ram and catback only
1996 RS 5-speed

No, it's a GST. FWD.

i would do the easy things first. check the balance of the tires. my car had the same problem at higher speeds and one of the front tires had a little less pressure and wasn't completly blanced from les schwab. good luck -Scott

Finally found the problem. While he was running the car, I got out of the window and check on the tires. Well, the whole wheel/tire were shaking. I lift the car and found out that the upper ball joint in the passenger side suspension arm had axial movement. All engine mounts were Ok.

If your ride is lowered for some time now and has some vibration, please check your ball joints. It is very risky to run the car like this. Dealer price for upper suspension arm - around $134.00 + tax.
Or find one in good condition on a salvage yard for around $40.00 to 50.00.

Well hope that everybody having a small vibration on the rides check their suspension components.

Thanks.



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges

nice response to an old thread! I thought i was never gonna hear the solution to that problem and wasjust thinking "bummer" about it a week ago or so...

sweet!

Pts when my computer stops giving me a blank screen...

---------------------------------------

Black 98 GST missing her owner and looking for a new one...Inquiries welcome

Yeah, it took a while before I could check his car again. But thank you. Hope this thread help somebody!



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges

wow this is weird . last week after hitting some major potholes ... after 65 i felt major vibration... the car shook like you couldnt belive. it was the entire frame. it stopped after than one ride.

1997 RS AUTO

ORACLE063
1/4 - 17.021
60' - 2.510
Weight 2730

Oracle: this is way off topic, but what kind of wax do you use? your sig pic looks awesome (my DSM is black too)...is it a repaint?

thanks@!
Vandy

---------------------------------------

Black 98 GST missing her owner and looking for a new one...Inquiries welcome

If it is shaking that violent, check your suspension parts (ball joint, link kits, etc) also your rims for a bended one. My frien damage his suspension on I-95 going to Tampa. He hit a spot around 75mph. His car is lowered so you can imagine the shaking. Hope you can find the damage part!



Stock Rebuild Block, Custom Turbo Kit: Custom 3" Downpipe, TEO4H Turbocharger : 10-12 psi, Starion Intercooler, Custom IC Piping, HKS By-pass, HKS AIC, (4) 330 cc extra injectors, Autometer Gauges