Hay everybody Im new to this forum but Iv bean working on my project for a few months now and have been posting my videos on YouTube. I though Ill share them with you guys so if you want to see my progress here is the links. I still have to make my latest videos but so far I have installed the AEM FIC and have the car on the road, thus beginning the break in process.
#44789, "RE: Project 420a GS Turbo" In response to Reply # 0
Haha, you annihilated that damn crank sprocket just like Hamelth.
Great videos and thanks for posting. Brought back memories! You know what you are doing, what platforms have you worked on before the 420a? Still never bought into the honing school of thought, but everything looked great.
So what model of the AIC do you have, what year is your car, and what do you have the AIC controlling? The AIC has had a lot of problems with our platform, I'd like to know how things have progressed.
Wish my brother would help out that much
2gnt: '99 RS-T, killed by a toyota, pending rebuild... Daily: Volt Daily #2: '99 EVG ebike- STOLEN by PEDRO
#44790, "RE: Project 420a GS Turbo" In response to Reply # 1 Jul-14-10 09:54 PM by dsmracr420a
If you used that gasket maker you were holding in the first video when you were talking about sealing the bedplate to actually seal the bedplate, then you're in for some problems down the road.
#44794, "RE: Project 420a GS Turbo" In response to Reply # 3 Jul-15-10 10:29 AM by RoninEclipse2G
Originally posted by TeamJC Why do you say that have you herd of a situation with that? The right stuff always worked out for me in the past.
The tolerances on the bedplate require anerobic sealant. The Right Stuff is too thick and won't allow the bedplate to be torqued down properly. It also won't cure without air. You'll either get leaks or a spun bearing. or both
Erik P. Official 2GNT thread Hijacker Some say that he's driven over more Covenant than he's shot, and that his grenades aren't where you'd expect them to be... All we know is, He's not The Stig... But he is The Stig's Spartan cousin!
Outside of Corona: "That sucks, peace out..." (jamie walks away)... "Sweeet, what we doin?" -Zac Tim's garage (prior to motor install): "Im gonna smoke real quick, that way if you fuck up I am already nicotined up" -Tim
#44798, "RE: Project 420a GS Turbo" In response to Reply # 5
Yup, not much I could do now. Ive used this stuff for 4g63s in the past and it worked awesome but this is my first 420a. I don't think It will have a problem curing because after one minute of exposure the sealant starts the hardening process, plus I used a very thin layer and the heat from the block should cause it to dry. Im more concerned with the clearance issue. I didn't think of that but the clearance can be effected. Ill use a thicker oil just in case but yeah if I could do it all over again I would just for the peace of mind.
#44792, "RE: Project 420a GS Turbo" In response to Reply # 1
I have a 98 GS. I installed a AEM FIC for fuel control. I still need to fine tune it but its running good but thoughs CEL, I guise Ill have to get use to it or put it on a switch.
Outside of Corona: "That sucks, peace out..." (jamie walks away)... "Sweeet, what we doin?" -Zac Tim's garage (prior to motor install): "Im gonna smoke real quick, that way if you fuck up I am already nicotined up" -Tim
#44978, "RE: Project 420a GS Turbo" In response to Reply # 0
So I didn't even put 600 miles on it and my speedometer stopped working. Turns out my speedometer drive gear came loose off of my drive axle, ouch. I must have had some water in my tranny that caused the nylon gear to expand and came loose. I should have flushed the tranny because it was sitting for a wile and i suspected some moisture. So now I have to pull my tranny out and tear it all apart to replace this $10 part. Well maybe I'll replace my differential with a LSD wile Im at it. This would be a good time to upgrade my clutch too but I don't have the extra cash right now, sux.
Outside of Corona: "That sucks, peace out..." (jamie walks away)... "Sweeet, what we doin?" -Zac Tim's garage (prior to motor install): "Im gonna smoke real quick, that way if you fuck up I am already nicotined up" -Tim
Search
Printer-friendly copy
1 User in Chat
