Does anyone have a front suspension diagram? I have a piece that needs replaced and nobody (Parts stores) know what the hell I am talking about. Its the front passenger side sway bar link. Anyway, anybody have a diagram so I can print it off and take it up there and show them? Thanks

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

They don't sell that at a general parts store. You'll need to go to a Dodge Parts Center... or a salvage yard.

Thanks, I found it at a local salvage yard. Appreciate it.

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

bone yards are great... too bad there is no 2g in a boneyard anywhere near me!!! i need a fender and a door. i would have also gotten some suspension parts from them too, but NO DAMN luck!!!

__________________________________
-Ryan

Where are you ^^^^^ at? I could possibly check for you if you want me to. I could call and find out the availability and how much for what you are looking for if you want. I could go buy the stuff and then you could paypal me the amount and pay for shipping. Let me know.

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

if you need the suspension diagram, its in the link in my sig. just click on the link and find where it says
2g_front_rear_suspension.pdf

dsm/mitsubishi service manuals https://www.mediafire.com/folder/5k14qlaulb9s1/dsm_mitsubishi

service manuals(my whole collection) https://www.mediafire.com/folder/ac51jwwa3g1n1/automotive_manuals

I have the same prob, all the bone yards near me have nothing newer than a 92. Freakin gay. I need a coolant res. and a passenger side side skirt for a 97+ GS/T/X.

GTAGRIP, would u mind checkin for me??

97 Eclipse GS
Saving for turbo, exhaust, and all that good stuff begins...

I'll give 'em a call today and check on the skirt, and reservoir (sp?). I'll let you know.

^^^Thanks for the diagram, I found it yesterday in your sig. Helped out a lot. Thanks

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

i'm too far for shipping, northern Illinois, close to wisconsin. i could probably just drive about an hour if i needed to.


thanks for the offer though

__________________________________
-Ryan

Sorry , wish I could help. Good luck to you!

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

when are you gonna post some pics of your new setup Jimmy??

Looks very nice IMO.

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

I'll try to get some pics up tonight. We found out that my rear drivers side hub assembly is bent (wheels wobble on that corner), plus EVERY SINGLE lug stud is breaking. I think last time I went to NTB they torqued them down to hard causing the thread to pull back, these lug nuts are a little longer and when you loosen them it sheers the thread and pulls it through. IT SUCKS!! But anyway, I'll get some pics tonight.

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

Sorry coClipse_97, they don't have either of the parts you are looking for.

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

What do you mean the hub assembly is bent....was it like that before? What happened ...any idea?? At least lug studs are a cinch to replace. Did you get your camber kit installed?? What about your alignment?

Sorry for the 20 questions....

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

I guess it was bent before. Who knows. I was putting the camber kit on the rear and spun the tire and it started wobbling. So I took off the wheel and put it on the other side. No wobble. The rear camber kit is installed and I am still waiting for the front. Should be here soon. Then alignment. Sam and I adjusted the toe on the front a little (without the alignment machine) so its not near as bad as it was and we adjusted the rear camber and it looks pretty good to the naked eye. Good enough for now.

DSM Registry Profiles:
http://www.dsmregistry.com/detail.php?carid=1410 (Eclipse)
http://www.dsmregistry.com/detail.php?carid=1411 (Talon)

Just read my feedback....hehe.....Yeah sorry for all the trash talkin!! I was in a crazy mood that night. It was awesome hangin out though. I had a good time. Thanks again for the eats! Can't wait to see the new and improved 2GNT back on the road.... Looks really good!!

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims