Okay, i got an underdrive pulley, now how the hell do I get the old crank pulley off??? I can get the bolt out, but the pulley is on there tight. Thanks.


95 Talon ESi

You have to get a REALLY GOOD crank pulley puller. I believe you can rent them at auto parts stores. I believe you want a 3 jaw 5 ton puller.




http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Contemplating turbo. . . . . . .
Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

http://www.extreme420a.com

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

does that mean it's that hard to put the new on on?

"In the end revenge sends end to the defendant"

yep... if you aren't mech inclined i wouldn't touch it.

All you need is the install tool. It has a ball bearing to let it tighten properly.

venomtalon@aol.com

Performance Mods: Custom CAI, Jeep 60mm TB, Ported Intake Manifold with Jeep TB match, 5 angle valve job, Head milled .020, Regrind Cams, PT Lifters and Rockers, AEM Cam Gears, OBX Wires, NGK Plugs, AFX UDP, OBX Header, OBX

Here’s the 10 step skinny:
1. Raise and block car, take off passenger wheel, unbolt plastic cover that you look at with wheel off. BAM, there’s the stock pulley!

2. Loosen alternator, AC compressor(if you have it), and PS pump. Take off belts.

3. Jack engine up under oil pan, just slight pressure at this point. make sure you put a piece of wood on the jack when jacking on the engine. If you jack directly on the oil pan it can bend up. Put the wood so it lifts on the edges of the oil pan.

4. Apply more or less pressure to take off tension on motor mount, remove mount on pulley side only.

5. Lower motor about 1-2in. (enough that the top of stock pulley will clear frame, you'll see what i mean)

6. Remove stock pulley bolt,(at this point go buy same thread bolt but 1-2in. longer and 5 or so thick washers that fit bolt, washers to be used later) screw 1in. of longer bolt into crank.

7. RENT A SMALL 4 TON GEAR PULLER from local auto store. This will need to be a 3 arm puller to fit on the INSIDE of the stock pulley. Now, pull off pulley.

***At this point if you don't know how to use a puller or can't figure it out, PAY someone to do this Mod for you!!!!***

8. Put on new AFX pulley and thread longer bolt with washers between head of bolt and pulley.

9. Use ratchet socket and bolt to "pull" new pulley on. You will need to wedge a screwdriver or similar tool between the pulley and motor to keep from turning the crank. Remove or add washers as needed to "pull" pulley on tighter. At some point you can put stock bolt back in to finish "pulling" on the rest of the way.

10. Add new belts, (the one that came with your pulley will most likely be for cars with AC. If you don't have AC you will need to get another belt. These numbers should be somewhat the same between different makers. 380K5/5050380DR)
tighten all acc. MAKE SURE BELTS ARE HELLA TIGHT or SSQQQUUUEEEELLLLL!!!!!!! put everything else back on and KAKOW, new pulley!!!

No matter how you do it, there will be some hassle. The old pulley is a tight bitch! You will need the puller!!!! You can try oven heating the new pulley to slide it on, but that method has mixed reviews and sometimes it works and sometimes it don’t. Plus you gota have good mittens to handle the heat! The way above will take about 3 hours from start to finish if you have all the right tools and are somewhat mechanicy inclined.




http://my97rs.homestead.com/mywebpage.html

I refuse to gently tip-toe through life, only to arrive at death, safely!

97 RS
Custom CAI
AF/X UDP
Bored TB-55mm
GS-T exhaust
"Super Good" plug wires
Front & Rear upper strut bars
Rear lower Stablizer bar
Front RRE lower Tie bar
Eibach Sportline Springs
Tokico shocks
Powerslot Rotors
S/S braided brake lines
Axxis Metal master pads
17" Focal Type 161's w/ Z-rated rubber
Stock shifter shortened 1.25in
Energy Suspension Shifter bushings
Custom shift plate(no more shift boot)
Indiglos
Grillcraft 3-pc. grill
V-Tech Taillight covers
Coming soon: AFC, EGT, A/F meter install, Pacesetter ceramic coated headers, 2.5" full exhaust pipeing

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)