Welcome to the 2GNT Forum!
Home Site Background Info & Specs Mods & Tech Info CAPS Part Reviews Donate 2GNT Stickers
Search Printer-friendly copy 0 Users in Chat
Top 2GNT Technical Performance/Engine topic #60406
View in linear mode

Subject: "Advice on Rod's" Previous topic | Next topic
Phat95EclipseRSSep-29-03 09:43 PM
Member since Aug 14th 2003
57 posts, 		Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#60406, "Advice on Rod's"


          

Ok, im rebuilding block for turbo... should i go for Crower or Eagle rods.. or something else.. post if you have info on which is b etter...

  
Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

Replies to this topic

pn0ymahalSep-29-03 09:50 PM
Donating 2GNT member
2621 posts, 		Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#60407, "RE: Advice on Rod's"
In response to Reply # 0



          

both are great rods. you get what you pay for. about 85% use eagle on this board.
Michael
99gs
HRC Stage IV 8-Injector Setup
2GNT Member #32

  
Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

RyaN95i4Sep-30-03 07:57 AM
Old School 2GNTer
2152 posts, 		Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#60419, "RE: Advice on Rod's"
In response to Reply # 0



          

Saenz...hold as much power as Crowers and are lighter

http://saenzperformance.com

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

  
Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

TeamMichael_97RSSep-30-03 02:42 PM
Donating 2GNT member
5866 posts, 		Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#60443, "RE: Advice on Rod's"
In response to Reply # 0

          

Unless you plan on making very serious horsepower the Eagle rods will handle the what you are throwing at them. You need a serious set up and high boost before you could even think about hurting the Eagle rods.



15.9 @ 86.7mph

Smooth idle? We don't need no stinking smooth idle.

Mods List:
http://highlander.dsmpower.com/sig.htm

  
Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

    
MotoFoolSep-30-03 05:41 PM
Member since Sep 08th 2002
2103 posts, 		Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#60467, "RE: Advice on Rod's"
In response to Reply # 3

          

saenz are good rods too...

Bill

You can have it cheap, fast or good. Pick any two.

If you want it cheap and fast, it's not going to be good.
If you want it cheap and good, it's not going to be fast.
If you want it good and fast, it's not going to be cheap.

  
Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

Top 2GNT Technical Performance/Engine topic #60406 Previous topic | Next topic
   

Powered by DCForum+ Version 2.2
Copyright 1997-2005 DCScripts.com, Copyright 2005-2026 2gnt.com
Generated in 0.063 seconds, executing 22 queries.