LAST EDITED ON 01-Nov-01 AT 08:40 AM (PST)

i know its only 100$ but where would i be able to get a 75mm one? and would i even need it? (i do plan to go turbo by this xmas**hopefully) i just sawthe dyno numbers and he's using the 55mm...i'm guessing if he's makin 13sec passes w/ it, it'll be fine for me for the time being

aem cai | greddy 4-1 headers | highflow cat | greddy sp cat-back exhaust | nx nitrous system - 75 shot | nos bottle heater | purge kit | steering mounted nitro/purge buttons | autometer carbon fiber gauges (a/f ratio, nitro press, oil press) | sprint performance 2" springs | b/m carbon fiber dash kit | symborski shifter kit

-bryan
'98 rst

I would not worry about going 75mm with a basic setup. You would end up needing a new mani to be able to match the flow. just go with the AFX.

MuRiX
97 Eclipse GS HRC Stage IV+
Sitting and collecting dust most of the time..
A.D.P.
http://www.murix.com

05 Mazda RX-8
06 Lotus Elise

Yeah unless you are really getting wild with everything, the 55mm will be fine. A switch to 75mm would need some massaging of the fuel system.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

mitselcps: If you go turbo by xmas you want to sell me Greddy header? Hook it Bro!!!!!


Mod List:
-NGK BKR5E-11 Plugs
-Magnecore 8.5 Wires
-AEM CAI(thanx to endless73)
-GS-T Muffler
-Upper Front Strut Bar
-Custom Short Shifter!

no more 420A

only 4G63

yeah, i will be looking for someone to take the headers and intake off my hands...if i can come up w/ about 1k, i should be able to get the kit...i have enought right now to get a stage 1 (or cheap stage2) online, but i'm opting for a custom setup (kindof like the star system) from a local shop...includes all parts, install, and tuning on a dyno. a lil more expensive, we'll see what happens.

but yeh, xmas hopefully.

aem cai | greddy 4-1 headers | highflow cat | greddy sp cat-back exhaust | nx nitrous system - 75 shot | nos bottle heater | purge kit | steering mounted nitro/purge buttons | autometer carbon fiber gauges (a/f ratio, nitro press, oil press) | sprint performance 2" springs | b/m carbon fiber dash kit | symborski shifter kit

-bryan
'98 rst

LAST EDITED ON 01-Nov-01 AT 01:23 PM (PST)

ps i don't suppose anyone has a cheap tb for sale? i can't be w/o my car for more than a day or two let alone 2 wks. are they cheap at junkyards? from mitsu maybe?

or would it just be better to pay 280$ for a new one from howell?

aem cai | greddy 4-1 headers | highflow cat | greddy sp cat-back exhaust | nx nitrous system - 75 shot | nos bottle heater | purge kit | steering mounted nitro/purge buttons | autometer carbon fiber gauges (a/f ratio, nitro press, oil press) | sprint performance 2" springs | b/m carbon fiber dash kit | symborski shifter kit

-bryan
'98 rst

Ray might let you rent his for $20 but hes kind of busy right now so...Sorry

Maybe someone else on the board would let you borrow theirs.

------------------------------------------------
98 ESi
95 GS

how much do you want to sell the headers for? email me.. im interested

Boca Raton, Florida
95 Eclipse GS- sold
99 Eclipse GSX- 386awhp
98 Eclipse GS- sold
92 Prelude

I contacted MS Recycling for a throttle body and they wanted 65 shipped not bad. You might also want to check mitsubishigraveyard.com

But I would love to get your headers when your ready to get rid of them. Hit me up with a price : grshper@pacbell.net


Mod List:
-NGK BKR5E-11 Plugs
-Magnecore 8.5 Wires
-AEM CAI(thanx to endless73)
-GS-T Muffler
-Upper Front Strut Bar
-Custom Short Shifter!

no more 420A

only 4G63

i just called ms recy. and they said 150$ ??

aem cai | greddy 4-1 headers | highflow cat | greddy sp cat-back exhaust | nx nitrous system - 75 shot | nos bottle heater | purge kit | steering mounted nitro/purge buttons | autometer carbon fiber gauges (a/f ratio, nitro press, oil press) | sprint performance 2" springs | b/m carbon fiber dash kit | symborski shifter kit

-bryan
'98 rst

LAST EDITED ON 01-Nov-01 AT 04:35 PM (PST)

i would be very interested in borrowing a tb for a few weeks, i'd pay 20$...can you get back to me on that? my email is mitseclps@yahoo.com (and that goes for anyone who might have an extra lying around)

http://plaza.ufl.edu/bryan01/personal
aem cai | greddy 4-1 headers | highflow cat | greddy sp cat-back exhaust | nx nitrous system - 75 shot | nos bottle heater | purge kit | steering mounted nitro/purge buttons | autometer carbon fiber gauges (a/f ratio, nitro press, oil press) | sprint performance 2" springs | b/m carbon fiber dash kit | symborski shifter kit

-bryan
'98 rst

Hey, i currently have Rays extra TB now, it will come off my car tomorrow. You may want to try and get a hold of him to see what he wants to do, but last i heard he's having a bad time, so if you dont want to get ahold of him i can see what he would like to do when i contact him...


http://my97rs.homestead.com/mywebpage.html

I refuse to tip-toe through life gently, only to arrive at death safely!

97 RS
Custom CAI
AF/X UDP
Bored TB-55mm
GS-T exhaust
"Super Good" plug wires
Front & Rear upper strut bars
Rear lower Stablizer bar
Front RRE lower Tie bar
Eibach Sportline Springs
Tokico shocks
Powerslot Rotors
S/S braided brake lines
Axxis Metal master pads
17" Focal Type 161's w/ Z-rated rubber
Stock shifter shortened 1.25in
Energy Suspension Shifter bushings
Custom shift plate(no more shift boot)
Indiglos
Grillcraft 3-pc. grill
V-Tech Taillight covers
Coming soon: AFC, EGT, A/F meter install, Pacesetter ceramic coated headers, 2.5" full exhaust pipeing

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

LAST EDITED ON 01-Nov-01 AT 07:01 PM (PST)

could you do that plz? thanks.

ps. did you just get a 55mm one? how did you like it?

http://plaza.ufl.edu/bryan01/personal
aem cai | greddy 4-1 headers | highflow cat | greddy sp cat-back exhaust | nx nitrous system - 75 shot | nos bottle heater | purge kit | steering mounted nitro/purge buttons | autometer carbon fiber gauges (a/f ratio, nitro press, oil press) | sprint performance 2" springs | b/m carbon fiber dash kit | symborski shifter kit

-bryan
'98 rst

Yea 55mm is as big as they can bore the NT TB. I just recently had an issue with my TB from howell where i was having idle surge problems. the problem was the TB plate wasn't cut nice and round, so it let air leak around the plate. i sent it back and they replaced the plate with a nice one and now its good as new, only better! No leak, no surge. I HIGHLY recommend the bored TB. Its worth the money! I will talk to ray now that mine is fixed and see what he wants to do. i'll let ya know...


http://my97rs.homestead.com/mywebpage.html

I refuse to tip-toe through life gently, only to arrive at death safely!

97 RS
Custom CAI
AF/X UDP
Bored TB-55mm
GS-T exhaust
"Super Good" plug wires
Front & Rear upper strut bars
Rear lower Stablizer bar
Front RRE lower Tie bar
Eibach Sportline Springs
Tokico shocks
Powerslot Rotors
S/S braided brake lines
Axxis Metal master pads
17" Focal Type 161's w/ Z-rated rubber
Stock shifter shortened 1.25in
Energy Suspension Shifter bushings
Custom shift plate(no more shift boot)
Indiglos
Grillcraft 3-pc. grill
V-Tech Taillight covers
Coming soon: AFC, EGT, A/F meter install, Pacesetter ceramic coated headers, 2.5" full exhaust pipeing

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

mitseclps: Damn man they told me 65 for the TB. Strange!!

Would there be any way to get the TB after mitseclps is done with it?


Mod List:
-NGK BKR5E-11 Plugs
-Magnecore 8.5 Wires
-AEM CAI(thanx to endless73)
-GS-T Muffler
-Upper Front Strut Bar
-Custom Short Shifter!

no more 420A

only 4G63

I got one. How's like 40 sound? I need to get rid of it and don't want to rip you off either.
Mail me at Eclipseturbors@yahoo.com
Also let me know if you want the sensors for it too? I'd like to have a back-up TPS but if you want it I'll send it.

Shit is all apart. Typical...

Nick Boers does the i4 t/b's out to 58.12mm...hes impossible to get a hold of tho :/


http://www.asog.net/phantom/

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

LAST EDITED ON 03-Nov-01 AT 08:35 AM (PST)

erik: i emaild you.
tim97rs: if you could get a hold of ray that would be great, if not its ok too.

http://plaza.ufl.edu/bryan01/personal
aem cai | greddy 4-1 headers | highflow cat | greddy sp cat-back exhaust | nx nitrous system - 75 shot | nos bottle heater | purge kit | steering mounted nitro/purge buttons | autometer carbon fiber gauges (a/f ratio, nitro press, oil press) | sprint performance 2" springs | b/m carbon fiber dash kit | symborski shifter kit

-bryan
'98 rst

e-mailed him and just waiting for a reply...


http://my97rs.homestead.com/mywebpage.html

I refuse to gently tip-toe through life, only to arrive at death, safely!

97 RS
Custom CAI
AF/X UDP
Bored TB-55mm
GS-T exhaust
"Super Good" plug wires
Front & Rear upper strut bars
Rear lower Stablizer bar
Front RRE lower Tie bar
Eibach Sportline Springs
Tokico shocks
Powerslot Rotors
S/S braided brake lines
Axxis Metal master pads
17" Focal Type 161's w/ Z-rated rubber
Stock shifter shortened 1.25in
Energy Suspension Shifter bushings
Custom shift plate(no more shift boot)
Indiglos
Grillcraft 3-pc. grill
V-Tech Taillight covers
Coming soon: AFC, EGT, A/F meter install, Pacesetter ceramic coated headers, 2.5" full exhaust pipeing

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)