pulling my #7 for shortening....what do I re-torque it to when I put it back in??
__________________________
...just my $.02
95 GS

____________________________
My $.02
95 GS

cancel that....where can I get ARP head studs??
__________________________
...just my $.02
95 GS

____________________________
My $.02
95 GS

Get them from ARP http://www.arp-bolts.com

Greg Williamson
1999 Eclipse GS "Sport" (Sold)
Star Stage III
12.817 @ 109.36

did you break it? btw are you attemting to fix your manifold leak. let me know how it works cause if you can pull this off i might give it a try.

Chris Dishmon

"Fillet Mignon?!?!?! How about a big slab of tube steak for the pretty lady."

chrisdishmon@hotmail.com
http://klipzracer.homestead.com/index.html

I was just gonna shorten the factory one and re-torque it, then I read a vfaq on arp head studs and if my factory one is stretched(which is a safe bet w/95k on the car) then I could blow the gasket even faster. so I want to just get an arp and do it "right" so-to-speak.
__________________________
...just my $.02
95 GS

____________________________
My $.02
95 GS

so could you take it out from just your vavle cover gasket from being off and were there any special tools involved?

Chris Dishmon

"Fillet Mignon?!?!?! How about a big slab of tube steak for the pretty lady."

chrisdishmon@hotmail.com
http://klipzracer.homestead.com/index.html

Yeah you can take it off from just having your valve cover off. I tried it a few days ago. Actually its kinda weird, in an erlier post someone said that #7 was the only one you can take off without removing the cams but actually you can reach all of them. I went in and removed the #7 and grinded off the bottom of the bolt but it seems to have made the problem worse. I think what I'll do is go back in and loosen all the bolts and retorque them in proper sequence. By the way 7-10 are 20 lbs and 1-6 are 25 lbs.

Dean.

Yeah you can take it off from just having your valve cover off. I tried it a few days ago. Actually its kinda weird, in an erlier post someone said that #7 was the only one you can take off without removing the cams but actually you can reach all of them. I went in and removed the #7 and grinded off the bottom of the bolt but it seems to have made the problem worse. I think what I'll do is go back in and loosen all the bolts and retorque them in proper sequence. By the way 7-10 are 20 lbs and 1-6 are 25 lbs.

Dean.

hmmmm.....interesting. what are your thoughts on this project koolade?

Chris Dishmon

"Fillet Mignon?!?!?! How about a big slab of tube steak for the pretty lady."

chrisdishmon@hotmail.com
http://klipzracer.homestead.com/index.html

well, my thoughts kindof fall into what fungul said. I read a post on vfaq.com about installing head studs.

http://www.vfaq.com/mods/headstuds.html

in a nutshell....
the ones in our motor are designed to stretch, but only once, therefore they cannot be re-used because they will not properly torque down. if you re-use a bolt, you increase the chances of blowing your head gasket.

my plan:
get one arp head stud(if they'll sell me just one), shorten it, and replace just the #7

if I can't buy just one, I'll get the whole set and either sell them individually to the guys here for the same purpose....or...if I can get to all the bolts w/out pulling my cams, I may just replace them all.

__________________________
...just my $.02
95 GS

____________________________
My $.02
95 GS