Tizopic for shizzle mah nizzle, preferably, the tranny cooler line going from radiator to the tranny (driver side). Thanks!!!!!!!!!

Kris
"Someday............I'll have traction problems!!!!"
Tampa, FL
Pinoy Turbo 2GNT

1999 HRC Turbo RS
Stage 2
Auto with BOOST!!!!!!!!!!!!

I don't know but you can just unplug one end and see.

"Natty Ride"


http://dirty.thisfreedumb.com/

Watcha doin?

as far as I know, all trans coolers use 1/2" hose to connect them.

does that help?

peace
WIKKI


THAT is not f**king THAT!
THIS is f**king THIS!

Actually, I'm planning to install my cooler that's been sitting in my garage from who knows when. I just wanna make sure what the sizes are before I start pulling shit out. It's the tranny cooler from PermaCool.

Kris
"Someday............I'll have traction problems!!!!"
Tampa, FL
Pinoy Turbo 2GNT

1999 HRC Turbo RS
Stage 2
Auto with BOOST!!!!!!!!!!!!

>Tizopic for shizzle mah nizzle, preferably, the tranny cooler
>line going from radiator to the tranny (driver side).

The stock AT cooler lines are ID-5/16". Here's what I did and it worked GREAT. My B&M Race AT cooler came with 1/2" in & out ports. I installed a 1/2" Male to 3/8" Female fitting in each port. I then installed a 3/8" Female to ID-3/8" Barb fitting into each port. (All fittings from Home Depot). I pulled all my old tranny cooler lines and replaced them with 3/8" tranny cooler line from autozone. I had to buy 8 new clamps so the lines would completely seal to the old hard lines.

The brass fittings were in the bathroom plumbing dept. in Home Depot. I have part numbers if you need them.

Do you have a tranny temp gauge? It's a good thing for us AT guys to have!

Indeed, may I have those part numbers??? Thanks man!!!!!

Kris
"Someday............I'll have traction problems!!!!"
Tampa, FL
Pinoy Turbo 2GNT

1999 HRC Turbo RS
Stage 2
Auto with BOOST!!!!!!!!!!!!

Fittings made by WATTS AB

A-828 - PB110 MALE PIPE TO FIP BUSHING 1/2" X 3/8"
A-294 - PB225 I.D. BARB TO MIP ADAPTER 3/8" X 3/8"

That's exactly what's on the bags. Good luck and let us know how that Permacool works for ya!

How much and where did you get the tranny coolers? Is it worth while to have and do you get any kind of gain...or is it just to keep things cooler. dont know anything about it but would like to know, TIA

Walker
95 Minden Silver Klipz GS A/T
One day my car will be in one piece
AEM CAI, Pacesetter Exhaust, Ported TB, Pro-Kit w/ Tociko Blues, 17" Excel TZ-7s(Gunmetal),SilverNT's rear carpet kit(lovin it), Interfire 1200w amp pushin 2 kicker comp 12's

It's to cool down the tranny fluid. When pushing a lot of power/tq through the tranny or when using a high stall torque converter, the fluid heats up. The hotter the fluid is, the shorter the life of your tranny. Once it gets to a certain temperature, it looses it's lubricating properties. No gain other than a longer lasting tranny. Stock engines/trannys don't need an auxilary cooler. Hope that helps.

In other words...if modding an A/T get one.. coo preciate the help, so where and how much for a decent one...and how hard are they to install?

Sorry for all the Qs, but just tryin to be informed

Walker
95 Minden Silver Klipz GS A/T
One day my car will be in one piece
AEM CAI, Pacesetter Exhaust, Ported TB, Pro-Kit w/ Tociko Blues, 17" Excel TZ-7s(Gunmetal),SilverNT's rear carpet kit(lovin it), Interfire 1200w amp pushin 2 kicker comp 12's

About $50 from summitracing.com. The B&M supercoolers are good ones.

not tryin to beat a dead horse...but where would you mount the cooler?by radiator, front mouth, side well?

Walker
95 Minden Silver Klipz GS A/T
One day my car will be in one piece
AEM CAI, Pacesetter Exhaust, Ported TB, Pro-Kit w/ Tociko Blues, 17" Excel TZ-7s(Gunmetal),SilverNT's rear carpet kit(lovin it), Interfire 1200w amp pushin 2 kicker comp 12's

Behind one of the front bumper side ducts