how do you check it i thought it was by the clutch master cylinder?.yes or no.please help im a lil lost here

No, that is the clutch master cylander level you are talking about. Which pushes the clutch in.

To check the car you need to get the wheel off and right above the axle is a rubber plug. With the car level, the fluid should be right at the bottom of this hole.

Yes I don't like the location of this plug it is a pain. Every other FWD car I've checked has the plug in an easy spot soyou can check it with the tire on just by turning the wheel. I can't see getting a hand in there with the tire on. End of rant

"Claim Victory in your heart, and the universe will follow."
Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

Injen CAI w/ K&N Breather Filters, AFX UDP, 55mm TB, GS-T Muffler, FU/RU/RL STBs, Front NRG Susp. Motor Mount Ins., Red Silicone Hose Kit, 8.5mm Magnecor Wires, Bosch Rapidfire Plugs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads, S-AFC, A/F Meter

And in my Room: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, SS Clutch Line, Rear Motor Mount Ins., EGT

Waiting for from RRE: Front Lower Tie Bar

Waiting for: Intake Manifold being ported/polished

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

I don't understand how I'm supposed to keep the car LEVEL when I jack up one side to get the wheel off. Can I raise it, remove the wheel, and then lower it to what looks like stock height? Just a thought, oh and BTW I don't have a lift in my back yard.

Coo'
1997 RS
AEM Cold Air Intake
B&M Short Shifter
Trust Shift Knob
Trust EVO Exhaust
Front Upper Strut Bar
Rear Upper Strut Bar
AutoMeter A/F Ratio Gauge
'tis it

YOU don't have a lift in your backyard?? YOU Have to have one to belong to 2GNT And with a lift,you don't have to take the wheel off.

YES, You just jack it up ,remove the wheel and then lower the car to close to level.
GOOD LUCK

Ditto, that's what I did, pulled the wheel and lowered my hydrolic jack to what I saw as level.

"Claim Victory in your heart, and the universe will follow."
Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

Injen CAI w/ K&N Breather Filters, AFX UDP, 55mm TB, GS-T Muffler, FU/RU/RL STBs, Front NRG Susp. Motor Mount Ins., Red Silicone Hose Kit, 8.5mm Magnecor Wires, Bosch Rapidfire Plugs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads, S-AFC, A/F Meter

And in my Room: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, SS Clutch Line, Rear Motor Mount Ins., EGT

Waiting for from RRE: Front Lower Tie Bar

Waiting for: Intake Manifold being ported/polished

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.