...and how much does it cost?


ride__________95 Eclipse RS : 5 speed
power________Field SFC Hyper-R : Gude cams : Jeep TB : AFX UDP : ram air : test pipe : GST catback
suspention___Hurricane F/R lower strut ties : BOMZ F/R upper strut bars : ES inserts
sound________Kenwood KDC 5000 : Audiovox 8" sub toob : Xplod 222
shizzle_______AutoCommand remote start : dual air horns : Caspers o2 simulator(rear)
incomming___Bosal header(maybe), 14b turbosystem(eventually)
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

95 Eclipse RS : 5 speed
14.76 @ 94.72mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

3-400$

i think that fastfwd does it and a couple other its very expensive for the minimal gain u get

You can have it cheap, fast or good. Pick any two.

If you want it cheap and fast, it's not going to be good.
If you want it cheap and good, it's not going to be fast.
If you want it good and fast, it's not going to be cheap.

www.extrudehone.com is the only place that does extrude honing. It is a type of porting but it's $$$$. Hand porting is much cheaper.

________________________________________________________________________________________
Car Sold


http://hometown.aol.com/ohshootuhh/
www.Fast420A.com

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

Cool. Thanks guys.


ride__________95 Eclipse RS : 5 speed
power________Field SFC Hyper-R : Gude cams : Jeep TB : AFX UDP : ram air : test pipe : GST catback
suspention___Hurricane F/R lower strut ties : BOMZ F/R upper strut bars : ES inserts
sound________Kenwood KDC 5000 : Audiovox 8" sub toob : Xplod 222
shizzle_______AutoCommand remote start : dual air horns : Caspers o2 simulator(rear)
incomming___Bosal header(maybe), 14b turbosystem(eventually)
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

95 Eclipse RS : 5 speed
14.76 @ 94.72mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

just talked to a guy the other day,I called him to ask how much port and polishing the intake mani would cost he said upwards of a 1000 $$ for extrudehone to do it, I thought that was insane

www.artexmusic.com

97' grey gs/Greddy EVO catback/Greddy header/AEM cai/afx udp/dropped on 2" sprints

Just go to their site, they have all the prices listed on there. I think to P&P the intake mani is like 475 for a 2 piece. The only reason serious people go with them over hand porting is because you can;t reach alot of places by hand. They can reach every surface there is with their process. The place is not to far from my house back home and I have been there a couple times and it is pretty impressive on the before and afters for the stuff they do. IMO it's well worth the money if you have it.

if u need every little horsepower available it may be worth it though, hand port and polish vers extrude hone for performancevers money, is way off the extrude hone costs alot more and doesn't produce much more results at all for the extra 3-500$ u spend on it..

very nice product i like it but untill im rich i wont be doing it any time soon...

You can have it cheap, fast or good. Pick any two.

If you want it cheap and fast, it's not going to be good.
If you want it cheap and good, it's not going to be fast.
If you want it good and fast, it's not going to be cheap.