I am trying to install my 32lb injectors and the chiltons manual says to depressurize the fuel system. Well I disconnected the electrical harnes started the car and waited for it to die from fuel loss but it did not. It never even lost any fuel pressure WTF. How do I do this cause I know if I do not depressurize the fuel system, when I take off the fuel line to get to the fuel rail I will leak every where?
Thanks for any info,
Patrick
96 GS
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Patrick
96 GS
13.54 @ 106.94 mph on 15psi 21 May.04
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Did you disconnect the harness at the fuel pump???

~Blake

Do you have an inline pump also?

It was the harness under the meatal plate inbetween the two back seats. It is the metal plate with nothing else under it but the harness. My fuel guage did not read after I disconnected it. Oh crap I forgot about the inline with the Hahn kit. How do I stop that one too?
Patrick
96 GS
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Patrick
96 GS
13.54 @ 106.94 mph on 15psi 21 May.04
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Did you also tried opening the gas filler cap, and maybe, even disconnecting the fuel pump relay that's on the firewall, driver side?

___________
Kon C

"Sometimes, a man has to do what a man has to do."

What if I took out the fuse for the inline pump that should shut if off right?
Patrick
96 GS
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Patrick
96 GS
13.54 @ 106.94 mph on 15psi 21 May.04
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Yeah,but you will still have pressure in the fuel rail.Just make sure you have a shop rag handy.

~Blake

There are 2 covers. If your gauge didn't read after you unplugged the harness, then you disconnected the wrong one, you disconnected the sender. Try the other cover, and don't forget to disconnect the inline. Should depressurize...
-=B-=

Dude, Boeing called. They want their wing back.

Dark0ne95: There is a butthole on that girl that his going to feel the wrath of 23 yeras of worldwide hate.
Me: Can I put that in my sig?
Dark0ne95: GO right fucking ahead.

yeah make sure you disconected the right one. the cover in the middle is the one for the fuel gauge i believe. the one behind the passanger seat is the one with the fuel pump.

dsm/mitsubishi service manuals https://www.mediafire.com/folder/5k14qlaulb9s1/dsm_mitsubishi

service manuals(my whole collection) https://www.mediafire.com/folder/ac51jwwa3g1n1/automotive_manuals

Yeah thanks guys I took off the other pannel and started unplugging everything so I got it to shut off. However now I have a bigger problem. I can't get the fuc$ing fuel rail off. I got the main fuel line off but had no clue how to get the actual rail off. There is not very much room to work with at all. Can you guys help me out have you guys taken off your fuel rails to replace injectors. I already installed the 2.72 disk and ring in my s-fmu so this is all I need to run 13psi. Thanks for any help,
Patrick
96 GS
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Patrick
96 GS
13.54 @ 106.94 mph on 15psi 21 May.04
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

there are 2 bolts to the intake manifold. Once they are out, it should be easy enough to remove. There are only 4 injector o-ring seals holding it in place. I don't know the proper method for removing the 2 bolts, but I did it the hard way by removing the engine and throwing in a 2.4...
-=B-=

Dude, Boeing called. They want their wing back.

Dark0ne95: There is a butthole on that girl that his going to feel the wrath of 23 yeras of worldwide hate.
Me: Can I put that in my sig?
Dark0ne95: GO right fucking ahead.

Are you talking about the two bolts on the braket that is perpendicular to the intake manifold? I will try to take that off now and see if it comes off. Thanks for the thought,
Patrick
96 GS
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Patrick
96 GS
13.54 @ 106.94 mph on 15psi 21 May.04
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies