I have all stage 1 and(0) done, and have always thought about port and polishing.

Is there any bad long-term effects from these mods?

Also, what kinda shop does this kinda work?

expenses??????

lemme know

Stage 1 in terms of what? Need to be a bit more specific please.

I'm going to assume from the stages on the main pages.

Go with the 55mm TB and P&P manifold. No ill effects reported by anybody here that has done it.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold 1/2, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, Crane Ignition Amp

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

yeah, stages as in intake, exhaust, well not new spark plugs because of lack of faith in how much that actually helps acceleration.

what kinda spark plugs am i looking for????

and i need more explanation on the p&p!!!!
i know very little about it! Please help!!

Your best bet is to go with Advanced racing Dynamics. They do p&P on our manifold for $80. Worth the money, everybody else withh probably charge you in the $250+ range.

The manifold is cast ina very rough manner the inside looks just like the outside of the manifold. NOT good for air flow. P&P opens up the runners and allows for more air to flow to the head and then smooths out the casting so the air flows smoothly, without turbulance.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold 1/2, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, Crane Ignition Amp

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

Heh for the record they should make a turbo stages mod, its not too difficult.

http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?