ok, I have a question that even the best around town can't give an honest opinion on. I recently bought the mopar windage tray for what I will call project 001. The car is currently equipped with arp bedplate studs. the windage tray comes with 4 "special" bedplate bolts with receving heads for the bolts that actually hold the tray to the engine assembly. so my question is installing this tray would mean removing half of the bedplate studs (one per bearing journal, zig zaging across) and replacing them with bolts. would doing this have adverse affects on the clamping force on the bedplate, and advertently damage my main bearings, or would I have to torque the bolts a little more than normal because there is a stud on the opposite side, or would I have to use ALL standard beadplate bolts and get rid of the studs, or is this idea not recommended at all for some reason.

bring it on............

A.D.P.
"...If you do too much, people become dependant. If you do to little, people loose hope. If you do it right, people won't be sure you've done anything at all."
bring it on...........

Where's Gary Howell when you need him?



current status unknown

http://hometown.aol.com/ohshootuhh/

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Drop in K&N Filter and open airbox
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

Whatever you decide to use to hold it on I would stay uniform for every one. Not mix and match studs and bolts. Different specs and stretching between the two. I would pick one and stick with it. Possibly see if ARP has an equivalant to the new bedplate bolts, or a stud that would accept the windage tray.

I wouldn't feel comfortable mixing the two, but I can't say that it would cause you any damage.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

I wouldn't even install it. If this is going on a 2GNT, from what i understand the Mopar windage tray for the Neon will not fit our cars, due to differences in the oil pan because of the location of our centermember as opposed to the Neon's.

I sure as hell wouldn't feel comfortable removing bedplate bolts for any reason other than crank removal and bearing replacement. Bearings actually bend slightly on the journal when they are torqued into place to for a more perfect circle around the crank.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

damn is there a picture of this windage tray? I hear good things about it but have never seen one. Do you have to take the engine apart to install it?

http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?

http://www.mopar.com/m_perf_parts_product_part.jsp?categoryID=10019&itemID=603

As long ashe got the one for the neon here's the link to the mopar site.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.