No I don't...

You just inspired me to work on my trunk setup. I ran into a little snag. I have 3 10's so OZ's setup was out of the question for me(Even though that 's what I really wanted.) I built a box(Sounds great!)This is similar to what I expect my setup to look like:


My problem is how do I make the top layer? I don't know how to measure it with all those curves in our trunks. I would like it to look flush.

Any help or advice would be appreciated.

http://www.snappydsl.net/ctoledo/

Cardboard... Keep goin and goin, til u get cardboard to sit right where u want it. Then go nuts, trace it, and cut away.

Bri...

yup, thats why i did.

take large card board boxes and cut them. i used several pieces, take one paice and cut it to match one side, take another peice for the other side, another peice for the back, etc... then tape them all together. once you have it right, trace it onto wood and cut.

easy as cake!



-johnny

"Few people understand
the psychology of dealing
with a highway traffic cop.
Normal speeders will panic
and immidiately pull over to
the side. This is wrong. It
arouses content in the cop
heart. Make the bastard
chase you, he will follow..."

http://homepage.mac.com/
johnnycorona/signature/logo.jpg

-johnny

"Few people understand
the psychology of dealing
with a highway traffic cop.
Normal speeders will panic
and immidiately pull over to
the side. This is wrong. It
arouses co

You almost made me start cryin dude!!

Yeah thats what I did too...Just used a bunch of cardboard pieces and taped them together to make a template. Good luck with your setup bro ...can't wait to see it!!

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

no, the easyest way to get the curves is with a gehto tool I make! Really just get a piece of long wirewith a loop at the end for a wire. Now with paper taped on the floor, now run the wire around the trunk and that will draw the curves.

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

yeah that actually how I made my little card board pieces it made myself a 8" strip of cardboard with a point on one end and a pen poked through on the other then just scribed one section at a time onto a piece of carboard. Then I just pieced it all together.

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

i used clear vinyl (stuff they use to cover living rooms). I actually still have the frame i used for testing if you want to test fit it in your car let me know, might not work the same since you'll need to go higher than i did with 3 subs.

jZa
IHS # fo-six-fo-six

"real men don't ride stick"

>i used clear vinyl (stuff they use to cover living rooms).
>I actually still have the frame i used for testing if you
>want to test fit it in your car let me know, might not work
>the same since you'll need to go higher than i did with 3
>subs.

You got mail.

http://www.snappydsl.net/ctoledo/