Okey, so here is the latest update... before i take the head in to have the tests done on it, I thought i would post some pictures of it to see if anyone see's anything that i don't. I also performed the oil test that etx suggested after cleaning the cyl walls from the lithium grease test over and over getting as much of the grease out as possible.

I centered the pistons and poored oil into all 4 cylenders... I cleaned the linoleem floor i placed under the lift so that i would notice any drips or leaks. I put the oil in the cylenders at aprox 6pm tonight and at 10:45 the oil was at the same level and no leaks on all 4 cylenders.


Here are some pictures

picture #1:

Wide picture of the oil in the cylenders #1-4

http://images.snapfish.com/3389%3B9%3A323232%7Ffp8%3Enu%3D3237%3E288%3E2%3C4%3EWSNRCG%3D323254%3B939%3B49nu0mrj

picture #2:

a closer shot of oil in cyl #1 #2 and part of #3

http://images.snapfish.com/3389%3B9%3A323232%7Ffp47%3Dot%3E2328%3D379%3D3%3B5%3DXROQDF%3E232345%3A%3A2%3A%3A%3A4ot1lsi

picture #3:

head shot of #1 combust chamber... i had a little oil in there from trying a test so the shiny oil stuff you see is just oil...i noticed some weird scar marks the make me ponder if the head gasket didn't make a complete seal.

http://images.snapfish.com/3389%3B9%3A323232%7Ffp47%3Dot%3E2328%3D379%3D3%3B5%3DXROQDF%3E232345%3A%3A347%3C3ot1lsi


picture #4:

full shot of head.. you can kind of see the weird scar marks i was talking about better in this picture

http://images.snapfish.com/3389%3B9%3A323232%7Ffp8%3Enu%3D3237%3E288%3E2%3C4%3EWSNRCG%3D323254%3B942729nu0mrj

picture #5:

an other shot of #1 this one is better quality... you can see the scars a little better

http://images.snapfish.com/3389%3B9%3A323232%7Ffp3%3B%3Dot%3E2328%3D379%3D3%3B5%3DXROQDF%3E232345%3A%3A33686ot1lsi

picture #6:
an other shot of #1

http://images.snapfish.com/3389%3B9%3A323232%7Ffp47%3Dot%3E2328%3D379%3D3%3B5%3DXROQDF%3E232345%3A%3A367%3C5ot1lsi

picture #7:

a closeup of one of the weird scars

http://images.snapfish.com/3389%3B9%3A323232%7Ffp8%3Enu%3D3237%3E288%3E2%3C4%3EWSNRCG%3D323254%3B945947nu0mrj

picture #8:

an other picture

http://images.snapfish.com/3389%3B9%3A323232%7Ffp47%3Dot%3E2328%3D379%3D3%3B5%3DXROQDF%3E232345%3A%3A368%3A5ot1lsi

any idea's?

Did you clean the head surface, or did it come off tha clean?

Originally posted by DarkOne
Did you clean the head surface, or did it come off tha clean?

i wiped it off a little... but for the most part it came off that clean...

Use a metal straightedge on your block and head deck surfaces? :shrug