LAST EDITED ON 12-May-01 AT 07:44 AM (PST)

I just snapped some pics of my intercooler pipeing, for thos who have been waiting to see what it turned out like.
Oh and just to let you know I have found an even cheaper way to make this custom set up than my earlier "jeg" u bend method.
This whole set up with RRE connectors and all ran me a total of $212.00
Here is what I used.
(1) pair of Flowmaster exhausts for a 1969 Camaro (new)
(2) 2"1/2 Hump connectors (RRE)
(1) 2" to 2"1/4 reducer (RRE)
(2) 2"1/4-2"1/5 reducer (RRE)
(1) 2"1/4 connector (RRE)
(1) 2"1/5 connector (RRE)
(1) Greddy BOV flange (RRE)
(18) Clamps
The bends on the flowmasters worked out PERFECTLY and was a cut and bead install. Click on my signature and go to the recent pics link.
Let me know what you guy's think.
SEE YA!!!!!!!!!!!!!!MWC



">
<img src="





http://smkn95eclipsemwc.homestead.com/mainpage.html

lol... it took me half an hour to find the right pictures.. :P .. looking nice.. so you basically had a stage 1 and upgraded to stage 2 with you own piping right?


ENKEI RP02 17" x 7"
AF/X UDP (still have to install:))
K&N Filter
springs/coilovers (still searchin' :D)






Junoon
97-RS
automotive/industrial design student :-)
Michigan

LAST EDITED ON 12-May-01 AT 02:38 PM (PST)

http://smkn95eclipsemwc.homestead.com/Uptodatepics.html



src="





http://smkn95eclipsemwc.homestead.com/mainpage.html

DAMN...Nice!!! I really like your cold intake:-) That's what I wanna do!! Was it hard to do?? Do you have a pic of it?? I really like it, nice job!!!



Ball Bearing Star Stage II
"Power is nothing without control"

DarkEclipseRS97 http://albums.photopoint.com/j/View?u=1574635&a=11969799&p=47132925&Sequence=0 Talenedt baby fuckin Talented!Damn Dog u got some skills peace!

Thanks guy's, I dont have a close up of the Cold air intkae but can snap one tomarrow and through it up on the board for you to see. It was too easy to make this set up. :)
The hardest part was cutting the pipes. :( (I had to use a hack saw).
The rest was "butter".
SEE YA!!!!!!!!!!!MWC

THAT'S TIGHT!:)

i saw them live and in the metal, so hahaha to you guys :)



javi d
vroom n' boom

lol, you are killing me JZA.
You are also one of the 2 on this board that has riddin in my car as well. :)
SEE YA!!!!!!!!!!MWC

So what IC is that? is it a star or is it from something else? How much did it cost and were did you get if from.

how did you make the bends in the piping?

LAST EDITED ON 17-May-01 AT 01:06 PM (PST)

The Intercooler is a Greddy I bought of e-bay, and I paid $365.00 plus shipping for it.
As for the bends in the pipeing, well they were all there to begin with. Thats why I bought and used the 1969 Chevey camaro Flowmasters, because looking at them I seen the bends were the type that I needed to run the pipeing the way I wanted to.
SEE YA!!!!!!!!MWC