Go back to previous topic
Forum nameTurbo/Nitrous Tech
Topic subjectHelp with 02 sensor CEL code
Topic URLhttps://forums.2gnt.com/dcboard.php?az=show_topic&forum=i8&topic_id=31449
31449, Help with 02 sensor CEL code
Posted by Semperboost, Sep-18-02 02:56 PM
I posted this awhile ago in the Performance section but got no response so Imma try this section:

AFter I washed my engine bay I accidently got the connector wet. So I turn on the car and my A/F gauge pegs to the last green and stays there throughout driving. It hesitates and surges when driving and idles off-beat. It threw the Check Engine and Autozone came up with the code 0132 O2 sensor sees more than 1.2v for 30 sec. I read the Service manual and it says when this happens the O2 sensor voltage shorts to the 02 sensor heater voltage. I take a Multimeter and get 13V for the heater and the O2 reads 9V..WTF?! I ditch the connector and short the wires together. Still the same - I just ordered a Bosch O2 sensor and am gonna install it this weekend. Thing I don't get is how could my 02 sensor get damaged electrically? Right now I cut the wires to the sensor to stop the funny idle. The A/F gauge stays center (yellow) and throws the CEL, but still runs OK. Please anybody with a clue help out. THanks
ALvin



96 RST
http://www.kaptainmyke.com/tir/gallery/SemperBoost
Star Stage I turbo kit /Starion I/C w/ 2" chrome piping / GReddy Type-S BOV / Missing Link / Custom APEXi- GReddy 2.5" exhaust / Nology wires / Dual Gaugepod pillar mount / APEXi EL mech boost gauge / Autometer A/F gauge / Southland Dual Friction clutch / B&M short shifter / Energy Suspension shifter bushings / 16" GSX Rims / Front/ Rear camberkits / Eibach Prokits / Tokico Blues/ Front Upper, Rear Upper/Lower strut bars / Rear GST sway bar
X-drilled rotors / Axxis pads / Stock GS/GST sideskirts /Color-matched center taillight/ door handles/ sideviews
Cleared Headlight turns/PIAA bulbs


31450, RE: Help with 02 sensor CEL code
Posted by XtremeRS, Sep-18-02 03:13 PM
sounds like the symptoms of a bad o2 sensor. Just be sure to double check all wiring, esp your A/F gauge tap connection. Be sure all connectors are dry, and not corroded any. Check the actual connection where your A/F gauge is, be sure it is dry, and tight.
31451, RE: Help with 02 sensor CEL code
Posted by Semperboost, Sep-19-02 01:41 AM
The A/F connection is tight..I even measured it at that point with a multimeter..I just hope it is not the ECU

96 RST


http://www.kaptainmyke.com/tir/gallery/SemperBoost
Star Stage I turbo kit /Starion I/C w/ 2" chrome piping / GReddy Type-S BOV / Missing Link / Custom APEXi- GReddy 2.5" exhaust / Nology wires / Dual Gaugepod pillar mount / APEXi EL mech boost gauge / Autometer A/F gauge / Southland Dual Friction clutch / B&M short shifter / Energy Suspension shifter bushings / 16" GSX Rims / Front/ Rear camberkits / Eibach Prokits / Tokico Blues/ Front Upper, Rear Upper/Lower strut bars / Rear GST sway bar
X-drilled rotors / Axxis pads / Stock GS/GST sideskirts /Color-matched center taillight/ door handles/ sideviews
Cleared Headlight turns/PIAA bulbs


31452, RE: Help with 02 sensor CEL code
Posted by XtremeRS, Sep-19-02 03:15 PM
check all your grounds. The battery, the ECU, and your A/F gauge to rule all that out too..