| Go back to previous topic | | Forum name | Turbo/Nitrous Tech | | Topic subject | What else do I need for my build up?? | | Topic URL | https://forums.2gnt.com/dcboard.php?az=show_topic&forum=i8&topic_id=2664 |
2664, What else do I need for my build up??
Posted by Shant, Mar-13-01 02:01 AM
Well as some of you know I have teh HRC stage 2 and after awhile my selas on teh pistons went, and proably a whole lot more, Anyways, I finally got my bottend end package from HRC, Pistons, Rods, Seal, Locks, etc, etc, Also have the 440cc and the S-AFC, I was wondering what Else I need, I start working on the car nect Fri, So far I need to go pick up the MLS head gasket set but what else, ANy and all input will help, mind you, this is engine only.
MLS is this top end and bottend end head gasket or just head gasket and need and seperate gasket kit.
APR head bolts and studs??? Where do I get these.
What else am I missing..thanks
Shant 98 Turbo Avenger
|
2665, RE: What else do I need for my build up??
Posted by Wyatt, Mar-13-01 07:08 AM
LAST EDITED ON 13-Mar-01 AT 01:09 PM (PST)LAST EDITED ON 13-Mar-01 AT 01:09 PM (PST)
LAST EDITED ON 13-Mar-01 AT 01:08 PM (PST)
Hey Shant,
You might also look into o-ringing the block if you want to get serous.
My mechanic recommended it and I have since then read many many times its a great way to better "seal" and protect the cumbustion chamber.
We used a copper o-ring with the MLS headgasket and so far everything has worked out great.
http://www.turbogs.com/engine_building/index.htm
Wyatt Leras
http://www.turbogs.com
98 Eclipse GS Star Stage 5,000 Turbo kit
|
2666, RE: What else do I need for my build up??
Posted by Shant, Mar-13-01 07:38 AM
LAST EDITED ON 13-Mar-01 AT 01:39 PM (PST)Thanks, Where can I get that copper o ring at?? Get my e-mail about your package??.. Herewis what I was going to get so far. kiku made these great suggestions
mopar valvesprings
MOPAR HI-PO LIFTERS!!!!
crane cam's titanium valvespring retainer.
second generation rocker arms
arp head studs.
Fluidyne radiator -
|
2667, RE: What else do I need for my build up??
Posted by RS_Guy, Mar-13-01 03:28 PM
Hehe, looks like you are falling into my "predicament" too....
Well in that case you could also add undercut valves, a 3/5 angle
valve job, port/polish the head, lighten the crank....
Oh and since everything is apart...change the clutch w/ lightened flywheel... :-)
Seriously though you might want to consider these Mopar Parts:
5014135-AC GSKT PKG 9001005
4798967-AC GSKT PKG 9001005
4728997 BRG PKG C 9032002 (4 Needed)
4729000 BRG PKG C 9032002 (1 Needed)
4728999 BRG PKG C 9032002 (4 Needed)
4667660 PUMP WATE 7042001
4667663 SEAL WATE 9011001
4667884 PUMP ENGI 9057001
4667283 TENSIONER 9020002
That is an MLT exhaust gasket, MLT head gasket, MLT bottom end gasket, Rod bearings, Crank bearings, water pump, oil pump.
You may want to add a timinng belt and new belts oh and don't
forget a Mopar oil filter. Also a valve cover gasket...
So where do we get a Copper O-ring from? My mechanic also reccomended one...
Thanks, and let me know if you need anything else.
Guy
RS_Guy
13.9sec @ 105mph passes
w/ Blown piston rings,
on Stock Internals
at 10psi Boost....
| |