thats what I'm lookin to find or fab,Any info on where some of you guys got yours would be greatly appretiated thx...

Mine is 8an stainless braided. All you need to do is setup your oil pan for a -AN fitting. Buy the hose ends and 12" of braided hose. Put it together and your golden.

I used -10, but yeah. same deal.

Originally posted by DarkOne
I used -10, but yeah. same deal.

x2

Originally posted by eclipse982nrRST

Originally posted by DarkOne I used -10, but yeah. same deal.

x2

I used -10 as well... Make sure if you are using T3/T4 turbo not to over tighten the AN end to the pipe threaded turbo flange.

Originally posted by eclipse982nrRST

Originally posted by DarkOne I used -10, but yeah. same deal.

x2

X3

Originally posted by djtrickee

Originally posted by eclipse982nrRST

Originally posted by DarkOne I used -10, but yeah. same deal.

x2

X3

x4
Aeroquip fittings / SS line here

Dont mean to hijack your thread but i dont want to make another either.

I plan on getting just a braided oil feed.

What kind of rubber hose would work for a return? Fuel line? I've got a half inch npt tap in my oil pan and i'm getting ready to pick up my fittings as soon as i can put the turbo and manifold on for mock up. Will fuel line be fine without melting from heat from the turbine housing?

Originally posted by 2GeclipseRS
Dont mean to hijack your thread but i dont want to make another either. I plan on getting just a braided oil feed. What kind of rubber hose would work for a return? Fuel line? I've got a half inch npt tap in my oil pan and i'm getting ready to pick up my fittings as soon as i can put the turbo and manifold on for mock up. Will fuel line be fine without melting from heat from the turbine housing?

Fuel line for a return line? Joking? You do know fuel hose is pretty damn small right?

If anything, use heater hose. I still would go with a stainless setup though as my experience with heater hose sucks.

Originally posted by totaleclipse_05

Originally posted by 2GeclipseRS Dont mean to hijack your thread but i dont want to make another either. I plan on getting just a braided oil feed. What kind of rubber hose would work for a return? Fuel line? I've got a half inch npt tap in my oil pan and i'm getting ready to pick up my fittings as soon as i can put the turbo and manifold on for mock up. Will fuel line be fine without melting from heat from the turbine housing?

Fuel line for a return line? Joking? You do know fuel hose is pretty damn small right? If anything, use heater hose. I still would go with a stainless setup though as my experience with heater hose sucks.

Heater hose wont hold up to oil.

Fuel hose is available in just about any size.

I am running -12an fittings and a .75" ID turbo drain line that was originally marked as braided diesel fuel line. If it can hold up to diesel, it should be fine for oil. Got it from napa, has a nice black textile braided covering, about $7/ft for the .75" ID ($5/ft for 5/8", $4/ft for 1/2"). Its a pretty decent hose, seems just as nice as the Earls Performance line I replaced with it.

Exactly what i was looking for. Thanks.

8 an here with a barb coming off the turbo and one on the pan as well. No clamps or anything all push on and had to cut it off when i had to change a fitting

www.stealthmodeperformance.com


I got told to check this place out by a friend for my oil lines.

Feeds for $42 shipped

Controllable-valved restrictors - $15 shipped

Oil pressure gauge t's and kits.

Braided return lines for $50 shipped

I also found a place online that sells competitively priced an fittings...


If guy doesn't get back to me about an oil feed line i pmed him about, i'm going with stealthmode.