I am throwing my bew turb spoile ron and i need to know how to remove the outside pieces of a 3 piece spoiler. Where are the bolts located? I couldnt find any bolts anywhere and i did a search too and no results.

if i'm thinking correctly, all the bolts or whatever, are on the inside of the quarter panel...remove the interior pieces in your hatch and look around on the metal there...

yep- on the inside of the 1/4 panel. Theres like a metal bracket for it

Evan B
97 GS
90 GSX
Stamford CT
EvMan2345@aol.com

waaaait, no need to go removing panels. if you want the sides off merely raise the trunk, and there are 2 screws that go into the side of the outer peice...they run horizontal. just unscrew those and pull off the peices. then to remove the brackets there are a couple screws that hold the bracket to the rear panel. for removing the large center peice you have to remove the lower portion of the hatch paneling. jsut 2 screws and a few pop clamps later its off. like 2-3 screws for the middle section, and there are screws/bolts that are on the very ends of the hatch assembly...usually covered by a black stopper lookin thing. then unhook the white connector which runs to the 3rd brake light, and remove the gromett. the entire process takes less then 5 min and you only have to remove 1 panel.

yeah, i got the center piece before. I just couldnt find the outside pieces. Ill let you know how it goes tomorow. Had to drill out every single bolt b/c they were all rusted to shit. Hope i dont need to do the same with the outside pieces.

Well i have doine everythign and i still havent found the screws. I took out the tailight and i dont see shit. I looked throughout the whole thign from the inside through the tailight whole and i havent see 1 fucking bolt. it is pissing me off. I need some help.

Also, every single part around the area on the inside of the 1/4 panel looks like it has been sealed up. i hope the previous owners didnt fuck around with anything

Originally posted by orzech
Well i have doine everythign and i still havent found the screws. I took out the tailight and i dont see shit. I looked throughout the whole thign from the inside through the tailight whole and i havent see 1 fucking bolt. it is pissing me off. I need some help. Also, every single part around the area on the inside of the 1/4 panel looks like it has been sealed up. i hope the previous owners didnt fuck around with anything

Did you look to the left side (on the right side) of the actual spoiler piece? Mine come right off with the 2 screws right there. Stop looking on the inside of the panel, it's on the side of the spoiler piece.

thank you, mine were sealed up or something, i have to chip away at that. that is a good reason why i can see the bolts. they are sealed. stupid ass previous owners.

i dont have any bolts on either sides of the spoiler pieces, WTF!!!!!

what should i do and where should i look? Everythign is completely smooth

OMG, you wont believe this. The poeple some how filled in the whole sin the 1/4 panels, filled everyhting in on the spoiler. And used reall, and i mean really heavy duty double sided stick tape. Strong enought hat it was almost bending my panel perminately. But i got teh spoiler off and i will have some pics of my trubo spoiler ASAP.

Thanks a lot for the pics and advice, i woulda been looking for htem damn bolts forever. hahahah

Finally got it all done, i need to finish patching the holes. I am using epoxy and mesh on the back side. And tehn i will fill them in with bondo. I have my own air paint gun so i can do everything my self. And there are no holes in the 1/4 panels:-) 225 bucks teh auto body place quoted me can kiss my ass.

Sorry to bring back an old post, but I tried searching, and I kept getting stuff related to "turbo" :S so that didn't work very well, but does the turbo wing bolt up the the same holes on the hatch as the middle of the 3 piece? I plan on going wingless for a little while until I can find a turbo wing.

no ut the cover the holes on the outside part of the hatch....you'll need to have the center part of the hatch filled/painted.. and the rear panals filled and painted....but you will need to redrill...