I have a 2 1/16 a/f ratio gauge and am trying to figure out where I can place it. I've seen people on these posts where they placed it on the cigarette lighter location which looked pretty nice, but I wasnt sure how they did it. If anybody has any new ideas or can post pics that would be nice, thanks.

P.S. Trying to think of other ideas besides using gauge pods. I currently have one of those air vent replacements that allows you to place three gauges, but decided to put the vent back on.

a pillar pod is a good investment dood...or the cool bezel pods that go around your steering hub and hold two gauges. The cigarette lighter thing is easy to install....jus cut the hole and mount it in and tap into neccessary wires...you could put it in your center consile someplace...maybe cut into your cup holder and put it there?? :shrug

^^^^ that is what I would do. I think the pillar looks better but it is harder to read. Plus I have heard guys on here say that their pillar and gauges got stolen. Good luck.

if you wanted to do the gauge in the cig lighter thing and still have the use of a power outlet, just move the cig lighter over to the hole where the lighting rheostat is. mine crapped out on me (rheostat) and i wanted to put a key'd nitrous switch where the factory lighter was anyways, so i just took out the non functioning rheostat and put in the cig lighter. i actually ended up getting an aftermarket lighter and putting it in there so no need to run the bulb wire and everything. when i get home ill take a pic of my setup. otherwise, if you wanted stealth you can put a gauge in the drivers side vent (the one in the door) or the one mentioned above that fits around the stock gauges

Thanks guys, Yeah i looked into the bezel gauges, that was my second option. But yeah, take those pics I really want to see them thanks :thumbsup

if you have any HKS Electronics to go along with this, (S-AFR, IPM, AIC, etc) i would look into getting a case from HKS.

it holds 2 HKS electronic components and a 46mm gauge and fits in a DIN slot beneth the radio
if you can get someone to do a really good job boring it for you, you can get it to 52mm. i did mine, and it was REAL close.

it is called the "Type-A" and they sat it is for a Nissan but with a little patience it will fit.

best bet is to look on e-bay since they are a JDM item, dont pay more than $30 though, its not that rare.
good luck

I custom put my A/F gauge in the A/C vent on the driver side door....looks bad ass IMO..... ill post a pix as soon as i can...

air vent on drivers side? damn that sounds badass

air vent on drivers side? damn that sounds badass, yea please post pics

http://www.2gnt.com/www/corbin/boost.html

:thumbsup

yup thats what mine looks like =o) juss mine is a/f and the custom plate doesnt have any screws...

Originally posted by bokchoi
I have a 2 1/16 a/f ratio gauge and am trying to figure out where I can place it. I've seen people on these posts where they placed it on the cigarette lighter location which looked pretty nice, but I wasnt sure how they did it. If anybody has any new ideas or can post pics that would be nice, thanks. P.S. Trying to think of other ideas besides using gauge pods. I currently have one of those air vent replacements that allows you to place three gauges, but decided to put the vent back on.

Hey, where did you get the pods for the center vents?

-------jezreel
hrc stage 1, sfmu, ml, prokits, egt, boost gauge, apexi tt, costum dp, dynotune fp gauge. gst muff, turbo spoiler

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!
thanks for www.kaptainmyke.com for the sig hosting :thumbsup

I got them on ebay but the last time I checked they didnt have any up for bid...but just check frequently I'm sure they should have it. Oh but just to let you know, it doesnt fit perfectly...it leaves a noticeable gap...so just looking out for you guys.