IM looking for a 8 or 10 point roll cage and have not been sucessfull any help would be appriciated
thanks
jason

try www.optauto.com i know they have some autopower roll cages.

i doubt you will find one already done. it will most likely have to be a custom deal. and if its an 8 or 10 point it will have to be a welded cage and not a cheezy bolt in show cage.

plumbing section at home depot has them

what kind of pvc should I use 2 inch or 4 inch lol thanks for the site yes I would like to get a weld in just seein if anybody knows where :-)

the pvc is a joke right? heh unless you want sharp fragments of plastic embedding themselves in every exposed section of flesh on your body upon impact... (ive made a couple PVC pipebombs in my past, they shatter nice and gruesomely, and if you put them in a full 55 gallon antifreeze barrel it will jump about 2 feet off the ground!)

Originally posted by silvrbullet
what kind of pvc should I use 2 inch or 4 inch lol thanks for the site yes I would like to get a weld in just seein if anybody knows where :-)

you do realize PVC is plastic, right?

Originally posted by tim97rs

Originally posted by silvrbullet what kind of pvc should I use 2 inch or 4 inch lol thanks for the site yes I would like to get a weld in just seein if anybody knows where :-)

you do realize PVC is plastic, right?

yes I do some peaple just respond with smart ass replies so I entertain them for a while I asked if anyone new where a good site was for roll cages not for some reply to go to home depot. Alls I know if I respond to someones question I try to come up with a intellagent replay
thanks for the concern though
jason

lol its straight, i figured you had to be joking because if you actually know its PVC and not PCV pipe (grah i hear it all the time, my mom cant understand the difference between a PCV valve and PVC pipe.), then you had to realise what you were saying :)

i could have sworn that mach v sold cages...not 10+ point though. It would prolly be easiest to find out where all teh local race cars get all theirs done, or check around at garages n whatnot.You'll save on shipping, and it would be easier to get it customized too.

yea I heard mach v too Im lookin for somthin differnt cause I fiberglassed my dash and I dont want run a cage through it. But I would like to have a 10 point cage so Im checkin out different vendors to see what the have or I will rent a pipe bender and make my own.
jason

I know this is off topic, but Buck Nutty, you should toon the backround in your sig.... that would look sick :thumbsup

Originally posted by silvrbullet
yea I heard mach v too Im lookin for somthin differnt cause I fiberglassed my dash and I dont want run a cage through it. But I would like to have a 10 point cage so Im checkin out different vendors to see what the have or I will rent a pipe bender and make my own. jason

you have to run the bar down threw yoour dash, to have a true 10 point cage.


DWAYNE H
1996 eclipse
under construction widebody eclipse, targa top, 19inch rollers, big brakes, 10 point custom cage, frank 2.4 hrc s20g turbo, custom marble paint job

2000 Yamaha R-1, 165rwhp 117 ftlbs tq

Originally posted by widebodied

Originally posted by silvrbullet yea I heard mach v too Im lookin for somthin differnt cause I fiberglassed my dash and I dont want run a cage through it. But I would like to have a 10 point cage so Im checkin out different vendors to see what the have or I will rent a pipe bender and make my own. jason

you have to run the bar down threw yoour dash, to have a true 10 point cage. DWAYNE H 1996 eclipse under construction widebody eclipse, targa top, 19inch rollers, big brakes, 10 point custom cage, frank 2.4 hrc s20g turbo, custom marble paint job 2000 Yamaha R-1, 165rwhp 117 ftlbs tq

Yea I seen your pics looks good was there anything behind your dash to remove to accomidate the bars
thanks
jason

acrually had to cut notches out in the frame thats going threw the dash.

DWAYNE H
1996 eclipse
under construction widebody eclipse, targa top, 19inch rollers, big brakes, 10 point custom cage, frank 2.4 hrc s20g turbo, custom marble paint job

2000 Yamaha R-1, 165rwhp 117 ftlbs tq

Competition Engineering makes an 8, I have one welded into my car. Go check out their site. If you want a 10 we've done the hoop conversion, put the X brace into it, and ran the two bars down to the floor. No you don't have to run it through the dash, you cut them back early and run them down near the A-pillar and then straight to the floor.