Go back to previous topic
Forum nameHandling/Suspension
Topic subjectWhere to get stuff for 15 dollar camber job?
Topic URLhttps://forums.2gnt.com/dcboard.php?az=show_topic&forum=i6&topic_id=8645
8645, Where to get stuff for 15 dollar camber job?
Posted by nappyjim, Apr-15-02 10:07 AM
I went to home depot and showed a guy the list, and he asked me if the bolts were in millimeters cause it shows, "M10x40" bolts. I was like, i dunno. So he said, well if thats millimeters than we dont have it.

So what size do i need? what does the M stand for? where did u get ur supplys?




18" Konig Tantrum Rims
Yokohama Parada Tires
H&R Sport Springs (Old Pic Above)
$15 Rear Camber Mod
AEM Cold Air Intake
ACS Black Molded Carpet
Interior Painted White/Blue (Soon to be silver/black)
Hyperwhite Lights
2 Rockford Fosgate XLC Subs
750 Watt All Digital Amp
Reverse Indiglo Gauges

Soon To Have:
Bored Throttle Body
Coilovers or Springs
Steering Wheel
Seats

8646, RE: Where to get stuff for 15 dollar camber job?
Posted by XtremeRS, Apr-15-02 10:42 AM
I had a hell of a time finding the bolts. Yes they are metric, and HOme depot should have some metric bolts, they are usually in the little slide drawers. They most likely will only have a few of them, i tried 2 home depots and each only had several of them. I went to about 4 or 5 differnet home building places befor i got them all. The measurements of the bolts are 10mm x 40mm(lenght) and the thread size is 1.25. I had some trouble finding the correct thread size too, most 10mmx 40 mm bolts were a 1.5 thread size. Good luck. It cost me over 20 bucks for everything too..
8647, RE: Where to get stuff for 15 dollar camber job?
Posted by Fast420A, Apr-15-02 02:26 PM
Home Depot's bolts are not the right grade rating. Go to Napa, pepboys, Dicsount Auto Parts, etc. . .

________________________________________________________________________________________
current status - No 3rd Gear synchro


http://hometown.aol.com/ohshootuhh/
www.Fast420A.com


8648, RE: Where to get stuff for 15 dollar camber job?
Posted by XtremeRS, Apr-15-02 02:59 PM
>Home Depot's bolts are not the right grade rating. Go to
>Napa, pepboys, Dicsount Auto Parts, etc. . .
>
I got the grade 8's at the depot. I think those are sufficient right? I think thats what i read anyway. The higher the grade, the better though...
8649, RE: Where to get stuff for 15 dollar camber job?
Posted by Fast420A, Apr-15-02 03:21 PM
I had gone to the Depot trying to find them and they only had one grade lower than 8. They also didn't have enough of each washer so I found everything at Napa.



________________________________________________________________________________________
current status - No 3rd Gear synchro


http://hometown.aol.com/ohshootuhh/
www.Fast420A.com


8650, RE: Where to get stuff for 15 dollar camber job?
Posted by proDMD, Apr-15-02 05:43 PM
I also tried home depot and they didnt have the bolts... so I got lazy and just ordered from RRE $40 should be hear any day now :)my prokit and KYB AGX should be on this weekend
8651, RE: Where to get stuff for 15 dollar camber job?
Posted by fasterGS, Apr-16-02 01:11 PM
NAPA.. got everything today for 15 bucks.