will 18x8" fit on my car?

do i need to do any fender rolling?
what happens if i lower my car, you think i'll have any problems?

i plan on using H&R OE Springs

it depends on how much u wanna drop. You will probably have to roll the inner lip on the rear fenders with a drop. 18x8 has been done. I am pretty sure a lot of the 19's you see on eclipses are 19x8. If 19x8 fits, no doubt 18x8 will. Go for it.

Look at my car (well former car) in the photo. Those wheels are 18x8 and the car is lowered 1.4 inches.

Mine's 18x7.5. I think. About rolling the fenders, it depends on how much u drop it. Mine's lowered on sportlines, so I definitely had to roll the fenders.

Oh yeah, aren't u the guy that goes to CSULB? There was a SoCal meet recently. So far, there's 4 ppl from CSULB. We plan on meeting up again prolly around Christmas time.

actually, really doesnt depend on the drop, just depends on the offset of the wheel, i could ride 225/40/18 at about a 3-4 inch drop(air ride) say for instance, if the off set is designed for a ford mustang,more than likely it will look slightly wide on a eclipse, (set out a lil) the offset on those wheels are like +47 and up stay under + 43 and u should be fine.

Dwayne H
A.K.A D-low
"PAID THE COST TO BE THE BOSS"

Exterior mods:
11 peice Kaminari wide body kit* custom fiber glass hood, PHAT* supra taillights* targa top* black/blue/chrome projectors* supra double stack wing w/ Carbon fiber top deck* shaved all body lines, shaved antennas.*
Suspension: Blowjax air cylinders* 3/8 inch electric valves* 1/2 inch lines* 5gallon air tank* 2 accumlators* strut bars
Rollers and stopies: 19x8 ACE menaces, chrome 225/19/35 front 275/19/35 rear AEM big brake upgrade (front Electronics (ALL): Msd ignit.
Apexi AFC *Apexi AVC-r*Apexi Rev/speed*Greddy TT*Automete A/F* Autometer Boost* Autometer volt* Autometer Fuel presure* Autometer water temp* Autometer egt*Autometer Oil presure*Autometer cluster bezel*Autometer triple pillar pod*Playstaion 2 fiberglassed in were passenger air bag used to be 7inch wide screen LCD*4 5 inch PB speakers ( 2 per door)*2 6x9 Pb speakers*
1 15inch PB extream sub* 1 1500 us amp* the whole dash, door sills,console, panes etc, is fiberglassed. the apexi components are molded in to the dash so you only can see the face (flushed)
Brand new Hrc manifold *Brand new Hrc 16g Turbo *Turboxs RFL BOV* Custom DOwn pipe 3inch 2 N1 Apexi Canisters*( the real deal, not that Ebay bullshit)race cat *
i need a good front mount intercooler, and some bodys stage 2 piping that they dont need or i will have to get it customized J.E pistons* Eagle specialty rods*5angle port and polish cam gears crane turbo cams bore TBbore intake manny maybe some High performance valves.Underdrive pullysstage 4 clutch kit*8lb flywheel*walbro 255 490cc injectors ,chasis: 8 point rollcage with removable door bar. reinforces the roof, due to the targa top

thanks for all the info guys...

hey sonicyan.. yeah i am the guy from csulb. i see your car every once in a while around school. =)

im at CSULB too...can u tell in the sig?

18X7.5 on Skunk2's......mmmmmdroppp!