;###############################################################################
;## DO NOT edit this file in the MegaTune release directory, edit the copy ##
;## in your car-specific directory. That would be ##
;## ##
;## C:/Program Files/MegaSquirt/car1/mtCfg/settings.ini ##
;## ##
;## in the standard installation. ##
;###############################################################################


MTversion = 2.25

;-------------------------------------------------------------------------------
; Pick a base configuration.
; Exactly one of these configurations must be "#set" and all the rest must
; be "#unset".

#group CODE_VARIANT "Code Variant"
#unset DFI "David Hooke's Ducati FI "
#unset DUAL_TABLE "Guy Hill and Eric Fahlgren's Dual Table variant"
#unset MSNEDIS "James Murray and Dave Hayne's MSnEDIS ignition variant"
#unset MSNEDISmod "Roger Enns's MSnEDIS variant with staged injection"
#unset MSNS "Magnus Bjelk's MSnS ignition variant"
# set MSNS_EXTRA "James Murray and Phil Ringwood's MSnS extensions"
#unset MS_ECU "Robert Hiebert's EEC-IV replacement code"
#unset MS_I "Bowling and Grippo MegaSquirt"
#unset MS_II "Bowling and Grippo MegaSquirt-II"
#unset PIC_SQUIRT "PIC squirt"
#endgroup

;------------------------------------------------------------------------------
; Pick an idle air controller setup, exactly one of these must be #set and the rest
; must be #unset. Only known to be valid for MegaSquirt-II.

#group IDLE_CONTROLLER "Idle Control Gauge Type"
#unset FIDLE_GAUGE "ON/OFF Fidle Valve"
#unset PWM_GAUGE "PWM Idle Valve (e.g., Ford or Bosch)"
# set IAC_GAUGE "Stepper motor IAC controller (e.g., GM)"
#endgroup

;------------------------------------------------------------------------------
; Pick an O2 sensor setup, exactly one of these must be #set and the rest
; must be #unset. None of this is applicable to MS-II, see all the
; calibration options under the Tools menu when using standard B&G MS-II code.

#group LAMBDA_SENSOR "Lambda Sensor Type"
#unset NARROW_BAND_EGO "Narrowband Sensor"
#unset WB_1_0_LINEAR "Wideband in NB Emulator Mode, 0-1v 1.5:0.5 Lambda"
#unset AEM_LINEAR "AEM Gauge AEM-30-42xx"
#unset AEM_NON_LINEAR "AEM UEGO Controller AEM-30-230x"
#unset DIYWB_NON_LINEAR "DIY-WB or Tech Edge non-linear output"
#unset DYNOJET_LINEAR "DynoJet Wideband Commander"
#unset TECHEDGE_LINEAR "Tech Edge sensor giving 0-5V 9-19:1 AFR"
#unset INNOVATE_1_2_LINEAR "Innovate sensor giving 1-2V 10-20:1 AFR"
#unset INNOVATE_0_5_LINEAR "Innovate, PLX 0-5V 10-20:1 AFR"
# set INNOVATE_LC1_DEFAULT "Innovate LC-1 default, 0-5v = 0.5-1.5 lambda"
#unset ZEITRONIX_NON_LINEAR "Zeitronix Non-linear WB"
#unset WB_UNKNOWN "Wideband sensor but none of the above types"
#endgroup

#unset LAMBDA "Display Lambda instead of AFR in Gauges"

;-------------------------------------------------------------------------------

#group Fueling_Algorithm "Fueling Algorithms (Speed Density DEFAULT)"
; Some code variants have been modified to allow alpha-N, almost
; none have MAF support, so beware of partial implementations in
; ini files.

# set SPEED_DENSITY "Speed Density Fueling Algorithm (Off=Alpha-N)"
# unset ALPHA_N "Alpha-N fueling Algorithm"
# unset AIR_FLOW_METER "Use an Air Flow Meter rather than a MAP sensor for fueling algorithm"
#endgroup

#unset CELSIUS "Temperature Units"
; Turn this on to enable degrees C everywhere.

; Leave set if you have a modern video card with lots of color depth,
; unset to use Brad's "colors08b.ini" if you have an 8-bit/256-color map.
# set COLOR_24_BITS "Use Full Colors (Off=Restricted Colors)"

# set KPa "Gauges all in kPa (otherwise some PSI)"

#group MAP_SENSOR "Map Sensor Type"
#unset MPX4115 "MPX4115 - 115 kPa, Usually only on v1.01 boards"
#unset MPX4250 "MPX4250 - 250 kPa, Default MAP sensor since v2.2 hardware"
;obsolete GM300KPa "GM 3.0 BAR - 300 kPa"
; Incorrect info from http://www.aquamist.co.uk/sl/plist/pics/mapm/mapm.html
; Correct info from http://www.not2fast.com/electronics/component_docs/MAP_12223861.pdf
; Use MPXH6300A instead of GM300KPa, they have identical specifications.
# set MPXH6300A "MPXH6300 - 300 kPa" ; http://www.freescale.com/files/sensors/doc/data_sheet/MPXH6300A.pdf
#unset MPXH6400A "MPXH6400 - 400 kPa" ; http://www.freescale.com/files/sensors/doc/data_sheet/MPXH6400A.pdf
#endgroup

;-------------------------------------------------------------------------------