LAST EDITED ON 14-Oct-01 AT 04:07 PM (PST)

Wondering how large is our stock exhaust piping? 2"?

Thanx,
Karl
97 GS
http://www.dreamwater.org/eclipsedevo

i think its 2.25, and know its pressbent crap. a 2.5 inch will bolt right up to the cat, at least it did 4 me




Sean G
vegaspimpin 99 gs ounce edition (wish it was a Q P)
http://seangordon1.tripod.com

short ram intake w/custom dual ram air
2.5 catback w/5zigen muff
NGK BKR5E-11
8.5 mm magnecores
AFX UDP in da mail
hurricane gs shiftermod
symborski shifter kit

Nope, it's 2".

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

inside diameter is close 1 7/8



http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Yes! Inside diameter is just about 1 7/8". The pipe is really thick, so the outside diameter is about 2.25". You can gain some flow by switching to aftermarket 2.25" pipe.


Corbin
'95 ESI-T
HRC + FMIC

Corbin, where have you mearsured the pipe? I looked at the downpipe and at the muffler and both were 2" (outside diameter)

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

A while ago...I grabbed my dad's vernier caliper and measured near the cat. I got 1 7/8" inside and something a little under 2.25" outside. Thats why many people say we have a 2.25" exhaust stock. It may depend on where you measure...


Corbin
'95 ESI-T
HRC + FMIC