Hey whats up.
I got a rebuilt head with new valves, cleaned, 3 angle valve job the works. Well we put it in and fired her up and there are two holes (that are suposed to be there)near the drivers side that are shooting oil out of them?!? WTF?!?!?

ANY one.. anything?

Nick
97RS

turbo8u> shut your SUCK
ZAO684: NIPPLE warning...maybe>?
turbo8u> yea i was a window licker on the short bus in junior high

Never trust a drunk machinst with a drill.

Where are the holes? Pics? Description, maybe? Help me out here.

Only thing I can think of is that the machine shop pulled the freeze plugs and didn't put the new ones in...

I dont have pics... But they look like they should be for bolts. They dont have any threads. They are next to the intake mani runners. Closer to the driver side. One is a little bit higher up then the other.



Nick
97RS

turbo8u> shut your SUCK
ZAO684: NIPPLE warning...maybe>?
turbo8u> yea i was a window licker on the short bus in junior high

Originally posted by Collente
I dont have pics... But they look like they should be for bolts. They dont have any threads. They are next to the intake mani runners. Closer to the driver side. One is a little bit higher up then the other. Nick 97RS turbo8u> shut your SUCK ZAO684: NIPPLE warning...maybe>? turbo8u> yea i was a window licker on the short bus in junior high

Well I just looked on my car, and if the holes you are talking about are like right under the throttle body area, and next to the intake runner, both holes sort of diagonal from each other, then both of those holes on my car have threaded cap screw plugs in them. You will have to find the right plugs somewhere, possibly the dealer, or just go to a hardware store and look for allen head cap screws of the right size. Unfortunately, I dont know the size..I'd also use teflon paste on the threads to seal it up..

Here is a pic, only good one i could find. Its the upper left hand corner of the head right?? Those two holes? Cap plugs on mine here:

Originally posted by XtremeRS

Originally posted by Collente I dont have pics... But they look like they should be for bolts. They dont have any threads. They are next to the intake mani runners. Closer to the driver side. One is a little bit higher up then the other. Nick 97RS turbo8u> shut your SUCK ZAO684: NIPPLE warning...maybe>? turbo8u> yea i was a window licker on the short bus in junior high

Well I just looked on my car, and if the holes you are talking about are like right under the throttle body area, and next to the intake runner, both holes sort of diagonal from each other, then both of those holes on my car have threaded cap screw plugs in them. You will have to find the right plugs somewhere, possibly the dealer, or just go to a hardware store and look for allen head cap screws of the right size. Unfortunately, I dont know the size..I'd also use teflon paste on the threads to seal it up..

They are diag to each other, and are right were you described them. Appreciate it!

You are the man seriously.

Nick
97RS

turbo8u> shut your SUCK
ZAO684: NIPPLE warning...maybe>?
turbo8u> yea i was a window licker on the short bus in junior high

small red X there my friend.



Nick
97RS

turbo8u> shut your SUCK
ZAO684: NIPPLE warning...maybe>?
turbo8u> yea i was a window licker on the short bus in junior high

Originally posted by Collente
small red X there my friend. Nick 97RS

blaa with imagestation! Here ya go...

THANKYOU!!

Nick
97RS

turbo8u> shut your SUCK
ZAO684: NIPPLE warning...maybe>?
turbo8u> yea i was a window licker on the short bus in junior high

I "think" those are NPT threaded plugs. If so, shoul;dn't be hard at all to find.

First place I would look is the machine shop that did you head, because they should be free from them...



Exile Racing Technologies: http://www.exileracing.com
una salus victus
It's holding down the garage floor right now.