Go back to previous topic
Forum namePerformance/Engine
Topic subjectintake
Topic URLhttps://forums.2gnt.com/dcboard.php?az=show_topic&forum=i5&topic_id=3758
3758, intake
Posted by optimuspeterson, Jun-19-01 04:54 PM
i'm sure this has been asked before but what is the best intake to buy? I cannot have a cold air intake because it either raining or the ground is covered in snow half the year
3759, RE: intake
Posted by dsm1, Jun-19-01 05:12 PM
actually the AEM and Iceman come in 2 set-ups, so you could switch in case of bad weather.




3760, RE: intake
Posted by Michael_97RS, Jun-20-01 12:58 AM
I like my Injen. Originally bought it in the short Ram and then got the extension pipe. So I can run cold air or short ram. Since I generally leave my car in the garage in cold weather. I've only gone to short ram once. It was an absolute downpour and I was taking a road trip and my boddy told me he ran into som edeep standing water so I shortened it up. It's surprising you really can feel the difference in the short ram set up.

"Claim Victory in your heart, and the universe will follow."
Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

Injen CAI w/ K&N Breather Filters, AFX UDP, 55mm TB, GS-T Muffler, FU/RU/RL STBs, Front NRG Susp. Motor Mount Ins., Red Silicone Hose Kit, 8.5mm Magnecor Wires, Bosch Rapidfire Plugs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

And in my Room: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, SS Clutch Line, Rear Motor Mount Ins.

Waiting for from RRE: Front Lower Tie Bar

Waiting for: Intake Manifold being ported/polished, EGT, A/F Meter, S-AFC
3761, RE: intake
Posted by FuSi0N, Jun-20-01 03:04 AM
When you say "feel the difference in the short ram set up" is the difference a decrease or increase in performance on a short ram set-up?

97 RS in Union City CA
Mods: Injen Intake, 1.3" drop

join #2GNT on Dalnet IRC
3762, RE: intake
Posted by 9D9 MITSU RS, Jun-20-01 03:46 AM
Well, I have some experience with intakes. I had a short APC intake. I felt a difference over stock with it. I finally heard AEM CAI over and over. I went out and got one. I also got the bypass valve so I wouldn't have to worry about weather. Anyhow. I put it on. It made a difference even over the short intake. I really like it. You hae to pay for the CAI's though. Mine hit me for close to 300. I heard the Iceman isn't made very well, but that's just hearsay. I can't back it up. I think there are a few guys here with it. Ask them about the iceman. I only know the AEM.
3763, RE: intake
Posted by Michael_97RS, Jun-20-01 04:42 AM
Yeah, you can feel an improvement over stock with the Short Ram. But the Cold air is really the best. especially once you get some speed going. The filter is right behind the opening and it acts like a ram air intake right into the filter. the faster you go the more air you force in there.

"Claim Victory in your heart, and the universe will follow."
Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

Injen CAI w/ K&N Breather Filters, AFX UDP, 55mm TB, GS-T Muffler, FU/RU/RL STBs, Front NRG Susp. Motor Mount Ins., Red Silicone Hose Kit, 8.5mm Magnecor Wires, Bosch Rapidfire Plugs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

And in my Room: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, SS Clutch Line, Rear Motor Mount Ins.

Waiting for from RRE: Front Lower Tie Bar

Waiting for: Intake Manifold being ported/polished, EGT, A/F Meter, S-AFC