Been looking at the Tsudo's.... any opinions?

http://cgi.ebay.com/ebaymotors/ECLIPSE-GST-95-96-97-98-99-TSUDO-3-N1-CATBACK-EXHAUST_W0QQcmdZViewItemQQcategoryZ33630QQihZ011QQitemZ320109565016QQrdZ1QQsspagenameZWDVW

I have one. it's alright.

Originally posted by DarkOne
I have one. it's alright.

Im actually looking to buy this exact one too, it looks like the pipe goes over the axle, is this correct? any other options on good eBay cat backs? I used to have a magnaflow and loved it

Yeah, they go over the rear crossmember.

Originally posted by DarkOne
Yeah, they go over the rear crossmember.

Are there any advantages or disadvantages to going over it?

you will be able to fit a sway bar that hangs low

Originally posted by RfOeCnKdOeNr

Originally posted by DarkOne Yeah, they go over the rear crossmember.

Are there any advantages or disadvantages to going over it?

Yeah, it's a tight spot, and they have to dimple the exhaust to clear it. 2.5" or 2" fits fine, though.

Originally posted by DarkOne

Originally posted by RfOeCnKdOeNr

Originally posted by DarkOne Yeah, they go over the rear crossmember.

Are there any advantages or disadvantages to going over it?

Yeah, it's a tight spot, and they have to dimple the exhaust to clear it. 2.5" or 2" fits fine, though.

So the 3" wont fit over the cross memeber?

Originally posted by RfOeCnKdOeNr

Originally posted by DarkOne

Originally posted by RfOeCnKdOeNr

Originally posted by DarkOne Yeah, they go over the rear crossmember.

Are there any advantages or disadvantages to going over it?

Yeah, it's a tight spot, and they have to dimple the exhaust to clear it. 2.5" or 2" fits fine, though.

So the 3" wont fit over the cross memeber?

If they dent it, yeah. it's a close fit.

I plan on going with a 3 in. Tsudo exhaust down the road. Everyone who has it seems to like them a lot.

Originally posted by DarkOne
Yeah, they go over the rear crossmember.

Originally posted by DarkOne

Originally posted by RfOeCnKdOeNr

Originally posted by DarkOne

Originally posted by RfOeCnKdOeNr

Originally posted by DarkOne Yeah, they go over the rear crossmember.

Are there any advantages or disadvantages to going over it?

Yeah, it's a tight spot, and they have to dimple the exhaust to clear it. 2.5" or 2" fits fine, though.

So the 3" wont fit over the cross memeber?

If they dent it, yeah. it's a close fit.

^What he said, the Tsudo 3" purposely comes with a dent in the rear section to fit over the rear cross member. Aside from being a bit loud, I like the exaust, it's at least a deep note, plus it comes with a silencer if you want to use. Oh and fitment was perfect and it came with all the hardware to bolt it together, just not mount it (my stock bolts that hung the stock exhaust were rusted, so I needed new bolts to bolt the exhaust to the stock locations. Overall I'm satisfied with it.

Could anyone snap a picture of it from the rear of the car?

Originally posted by talon749
Could anyone snap a picture of it from the rear of the car?

I don't have an under shot, but I do have one of what it looks like exiting the rear gimme a minute

hey thanks! it looks like it has a little bit of a slant to the left?

Yeah I am just looking for something that has a deep tone and good flow for when I am turbo. Oh and I dont want to spend 600 dollars on an exhaust.

hey cs, what cat if any do you use with this exhaust?

Originally posted by talon749
hey cs, what cat if any do you use with this exhaust?

I have the concept illusions test pipe

Originally posted by cs82685

Originally posted by talon749 hey cs, what cat if any do you use with this exhaust?

I have the concept illusions test pipe

what kind of DP are you using? I'm stuck with using the stock / Hahn one for a while and I want to have a decent exhaust I also would like to use a real cat, or at least something that will remotely clean up emissions

Originally posted by talon749

Originally posted by cs82685

Originally posted by talon749 hey cs, what cat if any do you use with this exhaust?

I have the concept illusions test pipe

what kind of DP are you using?

The one that came with the star kit.