i am replacing my timing belt, and i have hit a brick wall at the crankshaft pully. i have tried a 3 jaw 5 ton puller, and all i suceeded in doing was bending the bolt, i even tried heating up the pully, and still no go... what should i do???

http://forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=77561&mode=full

http://forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=89703&mode=full

http://forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=103309&mode=full

http://forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=97980&mode=full

Originally posted by DR1665
forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=58627&mesg_id=58627&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=52276&mesg_id=52276&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=7360&mesg_id=7360&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=90191&mesg_id=90191&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=37366&mesg_id=37366&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=16748&mesg_id=16748&listing_type=search

Originally posted by bullettdsm
http://forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=77561&mode=full http://forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=89703&mode=full http://forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=103309&mode=full http://forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=97980&mode=full

Originally posted by DR1665 forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=58627&mesg_id=58627&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=52276&mesg_id=52276&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=5&topic_id=7360&mesg_id=7360&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=90191&mesg_id=90191&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=37366&mesg_id=37366&listing_type=search forums.2gnt.com/dcboard.php?az=show_topic&forum=4&topic_id=16748&mesg_id=16748&listing_type=search

+1 quoted cause he's right

Looks exactly like the one I used. My machinist lent me one to pull my old one off.

Originally posted by link16
Looks exactly like the one I used. My machinist lent me one to pull my old one off.

Except this one does not push against the crank bolt... This one uses those shafts to push against the inside of the crank. See if you can find one of these...