Just some miscellaneous stuff laying around. Don't have any pictures right now, just throwing it up to see who's interested.

Autometer Traditional Style 2-1/16"
- Voltmeter Gauge
- Mechanical Oil Pressure Guage.

2.5" High Flow Cat direct bolt in, about 25,000 miles on it.

I'm probably going to sell my Crane Ignition Amp and Screamin Demon Coil Pack to go with a full MSD set up, just for the hell of it.


Mufflers:

Flowmaster 2.5" offset in / dual out 14 body legnth, welded with hangers and attached to a part of a rear section.

Hooker Aero Muffler 2.5" center in / dual out. Inlet neck has been cut down, never used

Pacesetter Muffler w/ resonator tip, cut off the Pacesetter cat-back.

Magnaflow 2.5" offset in . center out, used about 5,000 miles. inlet neck cut down after weld and outlet has a good 12" of pipe welded on.


Also in the not too distant future I'll be selling my e-manage with support tool and injector harness.

If any of these things sound interesting shoot me an e-mail: michael@exileracing.com


Exile Racing Technologies
http://www.exileracing.com
Go that way, really fast, if something gets in your way... turn.

" Please include at least an estimate of what you are looking to get when selling parts. i.e. $100 OBO (or best offer) This helps cut through people who don't want to pay as much as you are asking. Makes life easier on seller and prospective buyer."

...technically this post should be deleted

but anyway:


how much for the oil pressure gauge?

Originally posted by turbo8u
" Please include at least an estimate of what you are looking to get when selling parts. i.e. $100 OBO (or best offer) This helps cut through people who don't want to pay as much as you are asking. Makes life easier on seller and prospective buyer." ...technically this post should be deleted but anyway:

go on with your bad self mr moderator....

Originally posted by siueclipse
go on with your bad self mr moderator....

oh shut up bitch.

michael, with the mechanical gauge can i use an electronic sender? i want the gauge in the cab, but not at the epxense of a high pressure oil line pointed at my face...you know?

Originally posted by turbo8u
michael, with the mechanical gauge can i use an electronic sender? i want the gauge in the cab, but not at the epxense of a high pressure oil line pointed at my face...you know?

I ran the mechanical guage in the car for years with the nylon line. I now have it run in with a ss line. You can run an isolator but it's not worth it. No you cannot run an electrical sender in there's no where to hook it up.

How's $60 shipped for the coil?

Exile Racing Technologies
http://www.exileracing.com
Go that way, really fast, if something gets in your way... turn.

sorry, but i could get it from howell for $69 new so not interested anymore. good luck with the other stuff tho

hey mike how much do you want for the hi-flow cat?
I've been thinking about sticking with the 2.5" parts I already have. Im just not sure about the specifics on the actual flow amount the average mandrel bend cat back can support. I am "assuming" it would flow enough to support 300whp or close. If it becomes a restriction we could use the hi-flow cat as a removable section to run open header at the track. What do you think??

Originally posted by totaleklipse97
hey mike how much do you want for the hi-flow cat? I've been thinking about sticking with the 2.5" parts I already have. Im just not sure about the specifics on the actual flow amount the average mandrel bend cat back can support. I am "assuming" it would flow enough to support 300whp or close. If it becomes a restriction we could use the hi-flow cat as a removable section to run open header at the track. What do you think??

She'll flow fine for you. Steve's running the same core on his V-6 Avenger pushing around 12-13 psi, no problems with flow.

How about $75 shipped, $65 if you pick it up?

Exile Racing Technologies
http://www.exileracing.com
Go that way, really fast, if something gets in your way... turn.

Originally posted by kain_99gs
sorry, but i could get it from howell for $69 new so not interested anymore. good luck with the other stuff tho

I thought they were $79.... How about $50?

Exile Racing Technologies
http://www.exileracing.com
Go that way, really fast, if something gets in your way... turn.

Originally posted by turbo8u
" Please include at least an estimate of what you are looking to get when selling parts. i.e. $100 OBO (or best offer) This helps cut through people who don't want to pay as much as you are asking. Makes life easier on seller and prospective buyer." ...technically this post should be deleted but anyway: how much for the oil pressure gauge?

Ehh... how's $20 shipped sound?

Probably have to buy a nylon hose kit for it or ss line. I'll look around and see if I can find one laying around the garage.

Exile Racing Technologies
http://www.exileracing.com
Go that way, really fast, if something gets in your way... turn.

Originally posted by Michael_97RS
I'm probably going to sell my Crane Ignition Amp and Screamin Demon Coil Pack to go with a full MSD set up, just for the hell of it.

So how much for the Screamin Demon? Also, do you mean you are gonna buy a msd set up for yourself, or =? i am slightly confused

Voltmeter Guage - $15
Oil Pressure guage - $20

Crane Firball Ignition amp with tach adapters - $225
* This is the old style dual tach adapters, I had to resolder one of them.

Screamon Demon - $50

High Flow Cat - Pretty sure Aaron's buying this.

Make me an offer on any of the muffler, they'll probably goup on e-bay.

Exile Racing Technologies
http://www.exileracing.com
Go that way, really fast, if something gets in your way... turn.