Welcome to the 2GNT Forum! Interested In Advertising with 2GNT?
Home | Site Background| Info&Specs| Mods & Tech Info | CAPS | Part Reviews | Donate | 2GNT Stickers | 2GNT Shirts and Swag
Search Printer-friendly copy 0 Users in Chat
Top Team 2GNT Community 2GNT Site/Forum Questions topic #1400
View in linear mode

Subject: "Rebuild Questions" This topic is locked.
Previous topic | Next topic
HighMileOct-17-11 09:53 AM
Member since Oct 17th 2011
1 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#1400, "Rebuild Questions"


          

Background:
95 Eclipse (no letters, base mode I suspect); non-turbo.
Serial number is Canadian (not a model that was sold in the U.S.); so I’m told by those trying to look up parts.

I'm in the process of rebuilding my first 420A engine and I've discovered a few issues with my engine kit. I had the bottom boiled, bored (0.020 over) and honed and I’m finding some discrepancies between what the 420A service manual says measurements should be and what I’m getting.

Top ring end gap measures .020 to .021in
Spec says: .009 to .020in
2nd Ring end gap measures .019 to .020in
Spec says: .019 to .031in

The measurements were taken near the top, ½-way down and near the bottom of the stroke, and no filling of the ring end was done before the measurements were taken. By the book I take the measurements to mean that the 2nd ring is right where it should measure, but the top ring is over the limit and I would expect it to measure near the bottom of the range.

Question #1: Should I have the ring set re-ordered and expect the top ring to measure near the bottom of the range or am I missing something?

The machine shop was having some difficulty ordering the right kit because they could not figure out if my engine was 1996cc or 1997cc.

Question #2: How can one tell whether theirs is the 1996cc or 1997cc engine, and will getting the displacement wrong make a difference in ring size, affecting the end gap measurements?


I had the machine shop press the rod pins off and back on to the new pistons; three pistons look right but one is backwards. The stock rods are notched on one side and all notches were originally on the intake side.

Question #3: All rods should be facing the same direction with respect to the “front” mark (dimple) on the piston tops, right?

Question #4: What happens if any of the rods are installed backwards?

The forum describes the 420A block as being “over-square”.

Question #5: What does “over-square” mean?





  

Report This Post to Admin Printer-friendly copy | Top

Replies to this topic

Global Ruler Of All ThingsDarkOneOct-17-11 10:02 AM
Donating 2GNT member
14915 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list Click to send message via AOL IM facebook Click to send message via ICQ
#1401, "RE: Rebuild Questions"
In response to Reply # 0




          

Wrong forum, but I see you've started a new topic in the right place.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse GS (garage deco)
'98 Talon ESiT (poor impulse control)
'99 Eclipse RS (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

  

Report This Post to Admin Printer-friendly copy | Top

Top Team 2GNT Community 2GNT Site/Forum Questions topic #1400 Previous topic | Next topic
Powered by DCForum+ Version 1.2
Copyright 1997-2003 DCScripts.com

DCF+ v1.2 generated this page in 0.331295013428 seconds, executing 12 queries.